Installation - EdilKamin SIDE series Installations-, Betriebs- Und Wartungsanleitung

IMPORTANT ADVICE REGARD- IMPORTANT ADVICE REGARD-
ING THE INSTALLATION ING THE INSTALLATION
Other than that described in this docu- Other than that described in this docu-
mentation, you are also asked to note the mentation, you are also asked to note the
following UNI standards: following UNI standards:
- no. 10683 - fi rewood heat generators: - no. 10683 - fi rewood heat generators:
installation requisites installation requisites
- no. 9615/90 - calculating the inner - no. 9615/90 - calculating the inner
dimensions of fi replaces. dimensions of fi replaces.
Particularly: Particularly:
- Before carrying out any assembly it is - Before carrying out any assembly it is
important to verify compatibility of the important to verify compatibility of the
appliance, as stipulated in UNI 10683 appliance, as stipulated in UNI 10683
standard, paragraphs 4.1 / 4.1.1 / 4.1.2. standard, paragraphs 4.1 / 4.1.1 / 4.1.2.
- When assembly is completed, the - When assembly is completed, the
installer must implement "start-up installer must implement "start-up
operations" and issue documentation operations" and issue documentation
as required by UNI 10683 standard in as required by UNI 10683 standard in
paragraphs 4.6 and 5, respectively. paragraphs 4.6 and 5, respectively.
Before installing the lining, the correct Before installing the lining, the correct
functioning of the connections, the functioning of the connections, the
controls and all moving parts must be controls and all moving parts must be
checked. checked.
Verifi cation must be carried out with the Verifi cation must be carried out with the
fi replace on and after having been on for fi replace on and after having been on for
a couple of hours, before covering the a couple of hours, before covering the
fi replace, so that you can intervene if fi replace, so that you can intervene if
need be. need be.
After which, the fi nishing operations After which, the fi nishing operations
such as: such as:
- setting-up the fi replace mantel - setting-up the fi replace mantel
- mounting the fi replace covering - mounting the fi replace covering
- pilasters, painting, etc. - pilasters, painting, etc.
are carried out, once the tests are com- are carried out, once the tests are com-
pleted successfully. pleted successfully.
Consequently, EDILKAMIN does not Consequently, EDILKAMIN does not
accept responsibility for expenses deriv- accept responsibility for expenses deriv-
ing from demolition as well as construc- ing from demolition as well as construc-
tion even if either occurs as a result, tion even if either occurs as a result,
after having replaced any damaged parts after having replaced any damaged parts
of the fi replace. of the fi replace.

INSTALLATION

Introduction Introduction
• SIDE fi replaces must be installed ac- • SIDE fi replaces must be installed ac-
cording to the instructions given below, cording to the instructions given below,
since the safety and the effi ciency of the since the safety and the effi ciency of the
system depend on correct installation. system depend on correct installation.
• Before installation, read these instruc- • Before installation, read these instruc-
tions carefully. tions carefully.
• EDILKAMIN declines all responsibili- • EDILKAMIN declines all responsibili-
ty for any damages deriving from failure ty for any damages deriving from failure
to observe these instructions and in such to observe these instructions and in such
a case the guarantee shall not be valid. a case the guarantee shall not be valid.
• SIDE fi replaces are supplied already • SIDE fi replaces are supplied already
assembled on disposable pallets. assembled on disposable pallets.
Protection of the building Protection of the building
All surfaces adjacent to the fi replace All surfaces adjacent to the fi replace
must be protected against over-heating. must be protected against over-heating.
The insulation measures to be adopted The insulation measures to be adopted
depend on the type of surfaces and how depend on the type of surfaces and how
they are constructed. they are constructed.
Hot air vents / grills Hot air vents / grills
The hot air exit vents must be placed at The hot air exit vents must be placed at
least 50 cm from the ceiling and 30 cm least 50 cm from the ceiling and 30 cm
from furniture. from furniture.
Position the grills and air exit vents at Position the grills and air exit vents at
the highest point of the lining, in order the highest point of the lining, in order
to avoid the accumulation of hot air to avoid the accumulation of hot air
within the lining itself. within the lining itself.
Position the air grills and exit vents to Position the air grills and exit vents to
that they are easily accessible for clean- that they are easily accessible for clean-
ing. ing.
Ornamental beams Ornamental beams
Ornamental wooden beams may be fi tted Ornamental wooden beams may be fi tted
in front of the fi replace casing, but only in front of the fi replace casing, but only
if they are outside the fi eld of irradiation if they are outside the fi eld of irradiation
and at least 1 cm from the casing itself. and at least 1 cm from the casing itself.
The cavity which insulates the orna- The cavity which insulates the orna-
mental elements and the casing must not mental elements and the casing must not
allow heat to accumulate. allow heat to accumulate.
Ornamental wooden beams must not be Ornamental wooden beams must not be
integral parts of the building integral parts of the building
- 20
-
Flooring in front of the fi replace Flooring in front of the fi replace
Flooring in combustible materials must Flooring in combustible materials must
be protected by a suffi ciently thick non- be protected by a suffi ciently thick non-
combustible casing. The fl oor protection combustible casing. The fl oor protection
must be: must be:
at the front: at the front:
- more than 30 cm in respect of the - more than 30 cm in respect of the
height of the fi re level from the pave- height of the fi re level from the pave-
ment and in any case less than 50 cm ment and in any case less than 50 cm
at the sides: at the sides:
- more than 20 cm in respect of the - more than 20 cm in respect of the
height of the fi re level from the pave- height of the fi re level from the pave-
ment and in any case less than 30 cm ment and in any case less than 30 cm
In the fi eld of irradiation from the In the fi eld of irradiation from the
fi replace fi replace
The structural elements constructed in The structural elements constructed in
combustible material or which have combustible material or which have
combustible elements and furniture combustible elements and furniture
must be placed at least 80 cm from the must be placed at least 80 cm from the
fi replace mouth, in all three directions: fi replace mouth, in all three directions:
in front, above and at the sides. in front, above and at the sides.
If the said elements or pieces of furni- If the said elements or pieces of furni-
ture are shielded by a ventilated anti- ture are shielded by a ventilated anti-
irradiation protection, a distance of 40 irradiation protection, a distance of 40
cm will be suffi cient. cm will be suffi cient.
Outside the fi eld of irradiation Outside the fi eld of irradiation
The structural elements constructed in The structural elements constructed in
combustible material or which have combustible material or which have
combustible elements and furniture must combustible elements and furniture must
be placed at least 5 cm from the outer be placed at least 5 cm from the outer
casing of the fi replace. casing of the fi replace.
In this space, environmental air must In this space, environmental air must
circulate freely. circulate freely.
No accumulation of heat must be cre- No accumulation of heat must be cre-
ated. ated.
Electricity lines Electricity lines
There must be no electricity lines in the There must be no electricity lines in the
walls or ceiling of the fi replace installa- walls or ceiling of the fi replace installa-
tion area. tion area.