Siemens SINUMERIK 840D sl Bedienhandbuch Seite 11

7.15 Technologische Funktionen aufrufen.........................................................................................232
7.15.1 Weitere Funktionen in den Eingabemasken ..............................................................................232
7.15.2 Überprüfung von Zyklenparametern ..........................................................................................232
7.15.3 Einstelldaten für Technologische Funktionen ............................................................................233
7.15.4 Zyklenaufruf ändern ...................................................................................................................233
7.16 Ab-/Anfahrzyklus programmieren ..............................................................................................234
7.17 Messzyklenunterstützung ..........................................................................................................236
7.18 Beispiel: Standardbearbeitung...................................................................................................238
7.18.1 Werkstückzeichnug....................................................................................................................239
7.18.2 Programmierung ........................................................................................................................239
7.18.3 Ergebnisse/Simulationstest........................................................................................................253
7.18.4 G-Code-Bearbeitungsprogramm................................................................................................255
8 Technologische Funktionen programmieren (Zyklen) ............................................................................ 259
8.1 Bohren........................................................................................................................................259
8.1.1 Allgemeines................................................................................................................................259
8.1.2 Zentrieren (CYCLE81) ...............................................................................................................260
8.1.3 Bohren (CYCLE82) ....................................................................................................................262
8.1.4 Reiben (CYCLE85) ....................................................................................................................263
8.1.5 Tieflochbohren (CYCLE83)........................................................................................................265
8.1.6 Ausdrehen (CYCLE86) ..............................................................................................................268
8.1.7 Gewindebohren (CYCLE84, 840) ..............................................................................................270
8.1.8 Bohrgewindefräsen (CYCLE78).................................................................................................274
8.1.9 Positionen und Positionsmuster.................................................................................................277
8.1.9.1 An-/Abfahren ..............................................................................................................................278
8.1.10 Beliebige Positionen (CYCLE802) .............................................................................................278
8.1.11 Positionsmuster Linie (HOLES1), Gitter oder Rahmen (CYCLE801)........................................281
8.1.12 Positionsmuster Kreis (HOLES2)...............................................................................................283
8.1.13 Positionen wiederholen..............................................................................................................285
8.2 Drehen .......................................................................................................................................287
8.2.1 Allgemeines................................................................................................................................287
8.2.2 Abspanen (CYCLE951) .............................................................................................................287
8.2.3 Einstich (CYCLE930) .................................................................................................................290
8.2.4 Freistich Form E und F (CYCLE940).........................................................................................293
8.2.5 Gewindefreistiche (CYCLE940) .................................................................................................295
8.2.6 Gewindedrehen (CYCLE99) ......................................................................................................297
8.2.7 Gewindekette (CYCLE98)..........................................................................................................306
8.2.8 Abstich (CYCLE92)....................................................................................................................309
8.3 Konturdrehen .............................................................................................................................311
8.3.1 Allgemeines................................................................................................................................311
8.3.2 Darstellung der Kontur ...............................................................................................................312
8.3.3 Neue Kontur anlegen .................................................................................................................313
8.3.4 Konturelemente erstellen ...........................................................................................................314
8.3.5 Kontur ändern ............................................................................................................................320
8.3.6 Konturaufruf (CYCLE62) - nur bei G-Code-Programm..............................................................321
8.3.7 Abspanen (CYCLE952) .............................................................................................................322
8.3.8 Abspanen Rest (CYCLE952) .....................................................................................................327
8.3.9 Stechen (CYCLE952) ................................................................................................................329
8.3.10 Stechen Rest (CYCLE952) ........................................................................................................331
8.3.11 Stechdrehen (CYCLE952) .........................................................................................................333
8.3.12 Stechdrehen Rest (CYCLE952).................................................................................................336
8.4 Fräsen ........................................................................................................................................338
Drehen
Bedienhandbuch, 07/2010, 6FC5398-8CP40-0AA0
Inhaltsverzeichnis
11