Technical Data; Assembly; Function; Operation - Scheppach Zweiräder Original Bedienungsanleitung

Environmental protection
Do not simply dispose of the machine, accessories
and packaging in the dustbin, but ensure that it can
be recycled. A small amount of effort on your part
can do a great deal of good for our environment.
Residual risks
Even though using the machine properly there
will always remain a residual risk which can't be
eliminated. From the type and construction of the
machine following dangers can occur:
- Ejection of parts of the cutting material
- Damage of hearing if no prescribed hearing protec-
tion is worn
- Inhalation of the cutting material
- This electric tool generates an electromagnetic
field during operation. This field can impair active
or passive medical implants under certain condi-
tions. In order to prevent the risk of serious or deadly
injuries, we recommend that persons with medical
implants consult with their physician and the manu-
facturer of the medical implant prior to operating the
tool.

6. Technical data

Engine:
Engine rating:
Engine working speed:
Working width:
Hoe blade diameter Ø:
Starting system:
Fuel:
Engine oil:
Tank capacity:
Weight:
Spark plug:
Depth: 130 mm
Measured acoustic power level L
K uncertainty: 2 dB(A)
Measured acoustic power level L
K uncertainty: 2 dB(A)
Guaranteed acoustic power level L
vibration value ahw: (left) 9.8 m/s
K uncertainty: 1.5 m/s
2
ATTENTION: The value of vibration emitted during
product usage may differ from the declared value
depending on the circumstances.
Safety measures to protect the operator are based
on an estimate of exposure under normal conditions
of use (taking into account all operating cycles such
as the time when the tool is shut off, when operating
empty or in use).

7. Assembly

1. At first check all parts of the device and place
them in front of you on the floor (Fig. 2/3).
4-stroke engine,
140 ccm
2.6 kW/ 3.5 hp
2800 rpm
560 mm
260 mm
reversing
starter
Unleaded petrol
min. 90 octane
max. 5%
bio-ethanol
0.4l (15W40)
1.2 l
34 kg
LG F6TC
: 71.9 dB(A)
pA
: 91.9 dB(A)
wA
: 96 dB(A)
wA
/ (right) 8.8 m/s
2 2
2. To enhance the stability of the machine mount
the depth stop (10) and fix it with pin (B) (Fig. 5).
3. Mount the handles (M) at the handle bar mount
(6) with the delivered bolts (Fig. 6).
4. Mount the blade extension (11.1) as shown in
figure (7).
5. Mount the blade guard extension (9.1) as shown
in figure (8).
6. Mount the accelerator (16) as shown in figure
(9).

8. Function

Throttle Lever (16)
It controls engine speed. Moving the throttle lever in
the directions shown makes the engine run faster or
slower.
Wheel (17)
The spring locks wheel bracket at different height
and distance from the tines. Pull the spring-connect-
ed wheel bracket downwards to raise the wheel in
the upper groove when tilling. Set the wheel down
when transporting the tiller. Tilt the machine back
until the tines clear the ground. Push or pull the unit
to the next location.
Depth Regulator Rod (10)
It regulates the tilling depth and helps the operator
control the direction and speed of the tiller.
Insert the depth regular rod in the groove at the rear
of the chassis, with the pointed end downward and
the side outward. Lowering the depth regulator rod
will slow the tiller and make it till deeper. Raising the
depth regulator rod will allow it to move faster and till
shallower.
To adjust the tilling depth:
1. Remove the pin.
2. Raise or lower the depth regulator rod to the de-
sired position.
3. Replace the pin.

9. Operation

Adding motoroil
m ATTENTION! OIL HAS BEEN DRAINED FOR
SHIPPING.
Failure to fill engine sump with oil before starting
engine will result in permanent damage and void
engine warranty.
1. Check the oil level and top up if necessary oil.
(Max mark on the oil level indicator) (Fig. 11/12).
2. Open the fuel tank cap (2) and fill the device
with regular unleaded gasoline. (Fig. 13).
3. Pivot the wheel (17) upwards until the locking
engages on the intended recess (Fig. 14).
4. Put the accelerator (16) into position (Fig. 15)
A= Full throttle
B= Idle
C= Stop
5. Set the throttle lever to the position "A".
22 І 39 22 І 39