Technical Data; Before Starting The Equipment - Scheppach MTE370 Bedienungsanleitung

5. Injuries caused by the rotating blade.
6. Health risks caused by electricity. When incor-
rect or damaged mains cables are used. Fol-
lows instructions in the manual Electrical Con-
nections.
Warning! This electric tool generates an electro-
magnetic field during operation. This field can impair
active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.

6. Technical data

Main Voltage
Power Input
Working width
Working depth
LpA sound pressure level
K uncertainty
LwA sound power level
K uncertainty
Vibration at the
handlebars
K uncertainty
Protection class
Protection type
Weight
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect work-
ing order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.

7. Before starting the equipment

Before you connect the equipment to the mains sup-
ply make sure that the data on the rating plate are
identical to the mains data.
Warning!
Always pull the power plug before making ad-
justments to the equipment.
The Electric Tiller is delivered unassembled. The
handles must be assembled and mounted befor us-
ing the Electric Tiller. Follow the operating instruc-
tions step-by-step and use the pictures provided as
a visual guide to easily assemble the machine.
24 24 GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Montage
n Important!
You must fully assemble the appliance before
using it for the first time!
Installing the central tubes
The central tubes (4) will be mounted one after an-
other at the frame tubing (5).
Lay down the first central tube (4) on the frame tub-
ing (5) and push the carriage bolt (8) through the in-
tended hole.
Make sure that square of the carriage bolt (8) fits in
the square of the central tube (4).
Subsequently the wing nut (9) will be mounted and
get hand-tighted. The same process also applies to
the second central tube (4).
230V~ 50Hz
Installing the Plastic cross-plate (Pic. 4-5)
1000W
Unscrew the tattping screw (10) from the cross-plate
365 mm
(5)
180 mm Push the throttle handle (1a) and the handle (1b)
through the holes of the cross plate and align the
82,5 dB(A)
drill-holes from the handles and the Plastic cross-
2,5 dB(A)
plate. Subsequently screw in the tapping screw (10).
92,5 dB(A)
0,7 dB(A) Installing the handles (Pic. 6)
Slide the handles (1a/b) between the central tubes
2,96 m/s
2
(4). The throttle handle need to be mounted on the
right side (seen in workdirection). The handle (1b)
1.5 m/s
2
need to be mounted on the left side. The power cord
II
should be guided between the central tubes (4).
IPX4
Now push the carriage bolts (8) through the intended
holes of the central tubes (4) and the frame tube (5).
7,6 kg
Make sure that the square of the carriage bolt (8) fits
in the square of the central tube (4). Then screw on
the wing nut (9) and tighten it by hand.
Laying the power cord (Pic. 7/9)
Plug on the cable clip (11) on the right central tube (4)
(seen in workdirection). Now clip in the power cord
(2) into the cable clip (11). The belt clip (14) will be
fixed on you trousers belt. Make a loop with the pow-
erd cord and guide it through middle of the belt clip
(14).
Now lay the power cord (2) around the intended hook
of the belt clip (14) an tighten carefully.
Blade roller installing (Pic. 12)
Push the blade roller (7) on the drive shaft (18) of
the machine. The blade roller (7) can be mounted
left or right side. Be sure that the holes of the blade
roller (7) and the drive shaft (18) are aligned. Now
push through the Screw M8 (17) and fix it with the
nut M8 (16). Lock the nut M8 (16) hand-tighten.
For uninstall: Proceed in reverse order.