Olympus DS-5500 Bedienungsanleitung Seite 8

Cards compatibility:
For a list of card compatible with the
recorder, please visit the product
homepage at the Olympus website
applicable to your region or contact
your Olympus reseller where you
purchased the product.
Notes:
• When initializing (formatting) a
card, confirm that no necessary
data is stored on the memory
card beforehand. Initialization
completely erases the existing
data on the card.
• Cards initialized (formatted) by
another device, like a computer,
may not be recognized. Be sure
to format them with this recorder
before use.
• The card has a service life. When
reaching the end of its life, writing
or erasing data on the card will be
disabled. In this case, replace the
card.
• If you use a PC card adapter
compatible with the card to save
or delete some data on the card,
the maximum recording time on
the card may be decreased. To
recover the original recording time,
initialize/format the card in the
recorder.
Inserting and ejecting a SD
card
Inserting a SD card:
Insert the SD card fully into the card
slot with the card facing the direction
shown in the illustration below, until
it clicks into place.
• Insert the card keeping it straight.
Card recognition:
After inserting SD card, the message
[Please Wait] will flash on the display
while the recorder recognizes the
SD card.
8
Ejecting a SD card:
Push the SD card inward to unlock it
and let it come out of the slot.
• Hold the card straight and pull it
out.
Notes:
• Inserting the card the wrong way
or at an angle could damage the
contact area or cause the card to
jam.
• If the card is not inserted all the
way into the slot, data may not be
written properly.
• When an unformatted card is
inserted into the card slot, the
recorder will automatically display
the format menu options.
• Use only cards formatted with the
recorder.
• Never remove the card while the
recorder is operating, as this may
damage the data.
• After pushing the card inward to
eject it, releasing your finger too
quickly may cause the card to be
ejected unexpectedly.
• The recorder may not properly
recognize the card even when that
card is compatible with it.
• The processing performance
reduces in a card when you repeat
writing and deleting. In this case,
format the card.
Setting battery type and time/date
When you use the recorder for
the first time after purchasing
it, or when the batteries have
been inserted without the device
being used for a long time, the
battery type setting screen and
the time/date setting screen will
appear. Also, the battery type
setting screen will appear after the
batteries are replaced.
• For further details, a complete
advanced version of the manual*
(PDF format) is available for
download at the OLYMPUS website.
* Available in English, French or
German.
Setting battery type [Battery]
1 Turn on the recorder.
• The battery type setting screen
will appear after displaying
message [Please select Battery].
Battery
Ni-MH
Alkaline
BACK EXIT
2 Press the + or − button to select
[Ni-MH] or [Alkaline].
[Ni-MH]:
Select when Ni-MH rechargeable
batteries are used.
[Alkaline]:
Select when alkaline batteries
are used.
• The setting status will appear on
the display as [ ] (Ni-MH) or [
Ni
(alkaline).
3 Press the OK/MENU button to
complete the setting.
Setting time and date
[Time & Date]
If you set the time and date
beforehand, the information when
the file is recorded is automatically
stored for each file. Setting the time
and date beforehand enables easier
file management.
1 Press the 9 or 0 button to
select the item to set.
Select the item from the "hour",
"minute", "year", "month" and "day"
with a flashing point.
Time & Date
10 14 2013
M D Y
5: 00
PM
BACK 24H EXIT
2 Press the + or − button to set.
You can select between 12 and
24 hour display by pressing the
F2 (24H) button while setting the
hour and minute.
• You can select the order of the
"Month", "Day" and "Year" by
pressing the F2 (D/M/Y) button
while setting them.
3 Press the OK/MENU button to
complete the setting.
]
Al