Herunterladen Inhalt Inhalt Diese Seite drucken

Self-Priming From Open Tanks/Containers And Natural Water Sources; Bleeding The Appliance; Use; Filling Oil/Petrol - Parkside PHDB 4 B2 Originalbetriebsanleitung

Vorschau ausblenden Andere Handbücher für PHDB 4 B2:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Self-priming from open tanks/containers and
natural water sources
Use the self-priming equipment supplied.
Intake filter
3 m reinforced suction hose
With this accessory the appliance can draw water to max. 1 m above the
water surface. This can take up to 1 minute.
Immerse the 3 m suction hose
out.
Connect the suction hose
intake filter
remains underwater.
Run the appliance without the hand spray gun
flows evenly out of the high-pressure hose
If no water flows out after 1 minute, switch the appliance off and
check the appliance. Once the water flows, switch off the appliance
and attach the hand spray gun
work.
It is important that the hose and coupling are of a good quality, tightly
fitted and that the seals are undamaged and inserted straight. Leaky
connections can impair the suction.

Bleeding the appliance

Remove the nozzle
.
Start the engine (see "Starting the engine").
Pull the trigger
on the hand spray gun
Allow the appliance to run until the water comes out of the jet pipe
without any air bubbles.
Switch off the appliance and screw the nozzle
 GB │ IE │ NI
12 
completely underwater to get the air
to the appliance and ensure that the
attached until water
.
and the jet pipe
so you can
several times.
back on.

Use

WARNING!
Switch off the appliance before making any adjustments or carrying
out maintenance work.
DANGER! RISK OF EXPLOSION! DO NOT SPRAY
FLAMMABLE LIQUIDS!
Place the appliance on a firm surface.
The high-pressure cleaner may not be operated by children.
(Risk of accidents due to improper use of the appliance).
The appliance generates a lot of noise.
Risk of hearing damage. Always wear suitable hearing protect when
working with the appliance.
The water jet coming out of the high-pressure nozzle exerts recoil
force on the gun. An angled jet pipe can also cause torque.
Therefore, hold the jet pipe and gun firmly in your hands.
Never aim the water jet at people, animals, the appliance itself or
electrical components.
Vehicle tyres/tyre valves may only be cleaned at a minimum spray
distance of 30 cm. Otherwise the vehicle tyres/tyre valves could
be damaged by the high-pressure jet. The first sign of damage is a
discolouration of the tyre. Damaged vehicle tyres are a source of
danger.
Materials containing asbestos or other substances that are harmful to
health may not be sprayed.
To protect the operator from water spray, wear suitable protective
clothing.
Always ensure that all hose connection are screwed tight.
The trigger of the hand spray gun must not be jammed during use.

Filling oil/petrol

When you use the appliance for the first time, unscrew the red oil inlet
screw
and add approx. 0.6 l engine oil (15W40). Use the funnel
to do this.
Unscrew the filler cap
and add standard commercial lead-free
petrol to the fuel tank
. The tank has a maximum capacity of 3.6 l.
Add fuel up to the red mark.

Starting the engine

CAUTION!
Before first use, add engine oil (15W40, approx. 0.6 l) and fuel
(regular unleaded petrol).
Check the fuel and oil levels; top up as necessary.
Provide adequate ventilation for the appliance.
Ensure that the spark plug/spark plug connector
CAUTION!
When starting using the pull starter
can cause injuries to your hand.
Wear protective gloves when starting.
Open the fuel tap
; to do this, move the fuel tap
position.
Move the On/Off switch
to position I \ I (in the left position).
Set the choke
are firmly fitted.
there can be a kickback that
to the "ON"
to the "ON" position.
PHDB 4 B2

Quicklinks ausblenden:

Werbung

Kapitel

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Ian 291647

Inhaltsverzeichnis