Multifunction Display; Before Startup; Moving Sweeper Without Engaging Self-Propulsion; Start Up - Kärcher KM 130/300 R LPG Originalbetriebsanleitung

Multifunction display

1 Operating hour counter
2 Charge warning lamp
3 Oil pressure warning lamp
4 Cooling water temperature warning
lamp
5 Motor suction air
6 Indicator lamp (not connected)
7 Indicator lamp - forward driving direc-
tion
8 Indicator lamp - reverse driving direc-
tion
9 Indicator parking light (option)
10 Warning lamp fuel reserve
- blinks for reserve
- illuminates when gas bottle is empty

Before Startup

Fold up the cab
In order to perform different tasks, you may
have to fold up the cab (optional) first.
Note: The cab must only be tilted while the
vehicle is on even ground (± 5 °).
 Open the cab lock.
 Tilt the cab up until the lock lever clicks
into place.
 Unlock the lock lever prior to lowering
the cab.
Lock/ release parking brake
 Loosen parking brake; press brake
pedal at the same time.
 Activate the parking brake; press brake
pedal at the same time.
22
Moving sweeper without engaging
self-propulsion
 Open engine cover.
 Turn the freewheel lever of the hydrau-
lic pump by 90 ° down on the side.
Caution
Do not move the machine for long distanc-
es without engaging self-propulsion; a
speed of 10 km/h should not be exceeded.
 After moving, fold the freewheel lever
up again.
Moving sweeper by engaging
self-propulsion
 After moving, fold the freewheel lever
up again.

Start up

General notes
 Read the operating instructions of the
engine manufacturer before start-up
and follow the safety instructions care-
fully.
 Park the sweeper on an even surface.
 Remove ignition key.
 Lock parking brake.
Install/replace gas bottle
Warning
Only use replacement cylinders with 11 kg
contents of tested models.
Danger
Risk of injury!
Follow safety regulations for LPG vehi-
–
cles.
Formation of crusts and yellow-frothing
–
deposits on the gas cylinder indicate
leakiness.
Cylinders must be changed only by in-
–
structed persons.
Cylinders containing propellant gases
–
must not be changed in garages and
underground areas.
Do not smoke and use uncovered light
–
while changing the cylinder.
While changing cylinders, first close the
–
locking valve of the LPG cylinder firmly
and immediately put the protective cap
on the empty cylinder.
 Loosen the screw on the safety bar and
swivel the bar upwards.
5
-
EN
1 Protective cover
2 Gas hose with union joint
3 Gas withdrawal valve
Replacing the empty gas bottle
If the warning indicator for reserve fuel
shows an empty gas bottle continuously
during operation, proceed as follows:
 Close gas drawing valve by turning it in
clock-wise direction.
 Stop the the machine and continue to
run it at idle speed until the motor shuts
off.
Note: This will ensure that all gas lines
are empty and that there can be no ic-
ing which would hinder starting the mo-
tor.
 Unscrew the gas hose (30-mm span-
ner).
 Screw the protective cap onto the con-
necting valve of the empty gas cylinder.
 Open the cliplock.
Installing a new gas bottle
 Replace the gas cylinder.
Observe the installation position of the
gas cylinder. The connection / ring
opening must point downwards.
 Unscrew the protective cap from the
connecting valve of the gas cylinder.
 Close the bracket closure.
 Screw the gas hose to the connecting
valve of the gas cylinder (30-mm span-
ner).
 Close the safety bar, and secure it with
a bolt.
Note
Connection has a left threading.
Warning
Open the gas drawing valve (3) only after
starting the appliance (refer chapter Start-
ing the appliance).
Inspection and maintenance work
 Check engine oil level.
 Check the water cooler.
 Check roller brush.
 Check tyre pressure.
 Adjust driver's seat.
 Shake off dust filter.
Note: For description, see section on Care
and maintenance.