Safety Information; Meaning Of The Safety Information - Parkside Performance Pwsap 20-Li F6 Originalbetriebsanleitung

GB
MT
– Storage .........................................0 – 45 °C
PARKSIDE Performance Smart battery
Smart PAPS 204 A1/Smart PAPS 208 A1/
Smart PAPS 2012 A1
– Frequency ƒ ................. 2400 – 2483.5 MHz
– transmitted power ........................ ≤20 dBm
Cutting disc .................................... A24QBF
(included)
Manufactured in compliance with EN
12413:2019
Disc rotational speed n
Disc speed v ................................ ≤80 m/s²*
0
Outside diameter ........................... Ø125 mm
Borehole ......................................Ø22.23 mm
Thickness .........................................≤1.2 mm
* The grinding disc must withstand a rota-
tional speed of 80 m/s.
Levels of noise and vibration were determ-
ined according to the standards and regula-
tions in the declaration of conformity.
The specified total vibration value and the
stated noise emission value have been
measured according to a standardised test
method and can be used to compare one
power tool with another. The specified total
vibration value and the stated specified noise
emission value can also be used for a provi-
sional assessment of the load.
WARNING! The vibration and noise emis-
sions may deviate from the specified values
during actual use of the power tool, depend-
ing on how the power tool is being used.
Try to keep the exposure to vibrations as
low as possible. An example of a measure
to reduce vibration exposure is limiting the
working hours. All parts of the operating
cycle have to be considered while doing so
(for example, times when the power tool is
switched off and times when it is switched
on but running without any load).
WARNING! Grinding thin metal sheet or
other well vibrating structures with a large
surface area can result in increased noise
exposure and a much (up to 15 dB) high-
er overall noise emission than the specified
noise emission values. Use heavy flexible
damping mats or similar to prevent sound ra-
diation from such workpieces. Take into ac-
count the increased noise emission and wear
appropriate hearing protection.
28
−1
........12200 min
max
X 20 V TEAM
The device is part of the X 20 V TEAM
series and can be operated with batteries
of the X 20 V TEAM series. Batteries of the
X 20 V TEAM series may only be charged
using chargers of the X 20 V TEAM series.
We recommend that you operate this ap-
pliance with the following batteries only:
PAP 20 B1, PAP 20 B3, Smart PAPS 204 A1,
Smart PAPS 208 A1, Smart PAPS 2012 A1
We recommend charging these bat-
teries with the following chargers:
PLG 20 A3, PLG 20 A4, PLG 20 C1,
PLG 20 C2, PLG 20 C3, PLG 201 A1,
PDSLG 20 A1, PDSLG 20 B1, PDSLG 20 B2,
Smart PLGS 2012 A1
Rechargeable battery and charger technical
data: See separate manual.

Safety information

This section deals with the basic safety in-
structions for using the device.
WARNING! Injury and property damage
due to improper handling of battery. Observe
the safety information and notes on charging
and proper use as shown in the instruction
manual for your battery and charger from the
series X 20 V TEAM. A detailed description
of the charging process and further informa-
tion can be found in these separate operat-
ing instructions.

Meaning of the safety information

DANGER! If you do not observe this
safety instruction, an accident will occur.
The result of which is severe bodily injury or
death.
WARNING! If you do not observe this
safety instruction, an accident may occur.
The result of which is likely severe bodily in-
jury or death.
CAUTION! If you do not observe this
safety instruction, an accident will occur. The
result of which is likely minor or moderate
bodily injury.
NOTICE! If you do not observe this safety in-
struction, an accident will occur. The result
of which is possible damage to property.