Zipro Colt Bedienungsanleitung Seite 19

EN
E03
The computer
failed to detect
speed sensor
signal for 15
seconds
E04
Communication
error
E05
Overload error
E06
Explosion-Proof
Protection.
Incorrect power
supply
E07
Nothing is
displayed
E08
EEPROM driver
error
E09
The controller is
in an inclined
position
E10
Transient
current
protection
E11
Voltage is too
high
E13
Communication
error between
the meter and
the controller.
The counter is
not receiving a
19
The controller is Contact the
damaged manufacturer's
service.
Sensor connection Contact the
incorrect manufacturer's
service.
Sensor plug Verify plug
connection connections. If it is
incorrect correct and the
problem persists,
contact
manufacturer's
service.
Sensor failure Contact
manufacturer's
service.
Incorrect Contact
connection or manufacturer's
damage to the service.
wires.
Motor failure Make sure the motor
has not burnt out. If
not, disconnect the
treadmill from the
mains and reconnect
it. If the problem
persists, contact
manufacturer's
service.
Too low rated Replace the
current in the controller. Contact
controller. the manufacturer's
service.
Current exceeds Make sure the weight
the rated value of the user does not
exceed the maximum
value for the device.
Supply voltage too Connect the device to
low the correct voltage.
Short circuit Contact
manufacturer's
service.
The safety key is Insert the safety key.
out
The driver is Contact
broken. manufacturer's
service.
The device is not Move device to flat,
placed on a flat stable surface, then
surface. restart.
Incorrect Contact
installation of the manufacturer's
driver. service.
Incorrectly Contact
mounted engine. manufacturer's
service.
The transmission Contact
part of the manufacturer's
treadmill is service.
blocked.
Check if the AC power is above 270 VAT or it is
unstable. If so, stop using the treadmill and
report it malfunction.
Damaged wires Contact
between the meter manufacturer's
and the controller. service.
Incorrectly Contact
connected socket. manufacturer's
service.
signal from the
drive.
E14 Check if the AC power is lower than 160VAC or
Voltage is too it is
low unstable. If so, please stop using the product
and report
malfunction.
The device does No power
not work
The safety key is
out
Short circuit
The ON/OFF switch
is not on
The running belt The running belt is
does not move not lubricated
smoothly enough
The running belt is
too tense
The running belt The running belt is
is skewed too loose
The drive belt is
too loose
WARRANTY
On behalf of the Warrantor, the seller grants a 24-month warranty in
the territory of the Republic of Poland starting on the date of sale.
The warranty for the product does not exclude, limit, or suspend any
rights of the Buyer under the Consumer Rights Act.
The warranty card can be found on the last page.
WARRANTY TERMS AND CONDITIONS
1. The warranty covers only latent defects attributable to the
manufacturer.
2. The claim shall be processed by the point of sale or technical
service under the warranty if the customer produces:
a. a valid and clear warranty card filled in properly with a
sale stamp and signature of the seller,
b. a valid proof of purchase with the date of sale,
c. the reported product or defective part.
In the case of a remote purchase, the warranty card is
valid solely with a proof of purchase (receipt/invoice).
3. The claim is resolved within 14 days of the report by the
Customer.
4. Manufacturing defects identified in the warranty period shall
be repaired free of charge within 21 days following the delivery
of the product to the point of sale or technical service.
5. If it is necessary to import parts for the repair, the warranty
repair period may be extended by the time necessary to import
the part, not longer than by 40 days.
6. Warranty exclusions:
a. mechanical damage and related defects,
b. damage and defects resulting from misuse and
inappropriate storage, assembly, and maintenance,
c. damage and wear of such consumable elements as
cables, belts, rubber elements, pedals, foam grips,
wheels, bearings,
and upholstery,
d. activities related to the assembly or maintenance that
are user's obligation in accordance with the manual.
7. The warranty shall not apply when:
a. it is past its validity period,
b. the customer had repaired or modified the product
using non-genuine parts,
c. the defect resulted from incorrect installation or a
failure to follow the rules of correct operation in
accordance with the manual,
Connect the device to
a power source.
Insert the safety key.
Contact
manufacturer's
service.
Turn the device on.
Lubricate the running
belt as per the
manual.
Adjust and centre the
running belt as per
the manual.
Adjust and centre the
running belt as per
the manual.
Contact the
manufacturer's
service.