Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EN
Fragile. Prone to damage. Proceed with caution.
Protect from humidity.
Attention, heavy product.
Store in a maximum of 4 layers.
OPERATION
Make sure the device has been assembled correctly before starting
the training.
•
Before your first training, get familiar with all the functions and
adjustments available for the device.
•
Some parts of the device may corrode. It is, therefore,
inadvisable to leave the device in a room with a high moisture
content. Take care not to allow the device (in particular
internal and electronic components) to be exposed to water,
beverages, sweat, etc.
•
The device is intended for adult training and is NOT a toy.
If you allow children to use it at your own discretion, you must
provide them with instructions of appropriate use and ensure
constant supervision.
•
This is not a therapeutic device.
•
Slight humming noise may be heard during operation due to
the inertial movement of the flywheel caused by the structure.
It does not affect the operation of the device.
For exercise bikes and elliptical trainers, any possible
humming noises heard when rotating the pedals backwards
occur for technical reasons and have no negative
consequences.
•
Noise emissions are greater when loaded.
•
Before each training, make sure the protective devices are
operational and bolt and plug connections are tight.
•
Wear appropriate (sports) shoes during the training.
MAINTENANCE
Carry out maintenance activities at regular intervals. The tasks listed
below should be carried out at least every 20 hours of operation.
•
Check moving parts of the device. If they need lubrication, use
a bicycle bearing grease.
•
Check the conditions of such parts as bolts and nuts.
Make sure they are tight.
•
Wipe the sweat off the device after each training. Make sure the
display does not come in contact with water or moisture.
•
Clean the product with soapy water only. Do not use cleaning
agents.
•
Store the device in a dry and warm place.
•
Do not expose the device to direct sunlight.
ENVIRONMENT
The device is delivered in a package to protect it against any possible
transport damage. The packaging is made from non-processed
material and can be recycled. Throw the materials to appropriate
colour containers for selective waste collection.
Protect the environment and do not throw used batteries
into household wastes. Return them to the point of sale
or a special recycling centre.
Used electrical equipment (including the computer and
power supply) are recyclable. Do not throw them out with
household waste as they may contain substances dangerous to the
health and environment. You can actively contribute to sustainable
use of natural resources and the protection of the natural
environment by handing the used device to a recycling centre for used
electrical devices.
17
ASSEMBLY
The device must be assembled carefully by an adult. In case of doubt,
ask a more experienced person for help.
•
Prior to the assembly, make sure the set contains all
the listed elements and whether none of the parts was
damaged during transport. If any parts are missing or you have
any other reservations, contact the seller.
•
Have a look at the drawings and explanations and follow the
assembly manual when assembling the device.
•
Be careful during the assembly. There is a risk of injury when
using the tools and parts.
•
Remember to keep your surroundings safe. Do not let tools
and parts lie around in chaos. Remember that plastic foil and
bags pose o suffocation risk to small children.
•
Assembly parts necessary for a specific step in
the assembly manual are shown in pictures and included in
instructions. Use the elements indicated in the assembly
manual.
•
Do not tighten parts completely during the first stages
of the assembly. Tighten connections after all parts are placed
and fitted properly.
•
The manufacturer may have assembled some parts.
ASSEMBLY DIAGRAM (→ See page 2)
ATTENTION! Do not use parts other than those provided by the
manufacturer.
PARTS LIST
NO.
DESCRIPTION
1
Main frame
2
Handlebar
3
Guide rail
4L/R
Handlebar arm
5L/R
Pedal bracket
6L/R
Roll bracket
7
Connecting joint
8
Crank
9
Handlebar
10L/R
Handlebar
11
Front base
12
Allen bolt M8*60
13L/R
Handlebar post cover
14
Allen screw Φ10*57 M6*16
15
Allen screw Φ10*45 M6*16
16
Allen screw M6*16
17
Screw M8*L45*Φ8
18
Computer
19
Allen screw M8*38*L12
20
Allen screw M8*20
21
Allen screw M8*16
22
Allen head screw M8*16
23
Hex head screw M8*40
24
Hex head screw M8*16
25
Hexagonal screw M8*20
26
Pan head screw ST4.2*18
27
Phillips head screw
28
Screw M8*55
29
Flat washerΦ17*Φ22*1
30
Nut
31
Flat washer D8*D32*2
32
Resilient washer D8
33
Flat washer D8*D20*2
34
Flat washer D8*D16*1.5
35
Axis of holders
36
Arc washer Φ8*1.5*Φ20
37
Axle Φ17*59
38
Corrugated washer D17
39
Roller
40
Nylon nut M8
41
Cap nut M8
42
Bearing 6003Z
43
Hexagon nut M10
QUANTITY
1
1
1
1+1
1+1
1+1
2
2
1
1+1
1
2
1+1
2
2
4
4
1
2
4
4
4
6
4
2
12
4
2
4
2
6
22
8
12
1
8
2
6
2
8
6
4
4
Werbung
