Werbung
Verfügbare Sprachen
Verfügbare Sprachen
!
Be aware
If a fault occurs, the blue LED will flash.
This is then an indication that the battery
is faulty and needs to be removed. The C3
charger will then not commit charging.
When the battery level is very low, it might
only be possible to adjust the height of
the walker down, not up. The battery must
be reset if this occurs. Take the battery
out of the control box and press the red
height adjustment button on the handle
(see section 4; height adjusting) until you
hear a beep.
Troubleshooting
Brakes
Worn out / defect wheel
Not braking effectively
Worn out / defect brake mechanism on wheel
Worn out / defect brake handle
Worn out / damaged brake cable
Height adjustment
Battery is flat/does not work
The height adjustment does not work
Height adjustment goes down, not up
The battery is not correctly mounted
Loose cable contact
Damage on the cable
Defect switch
Defect height adjusting panel (accessory)
If all the above has been checked and the product is still not operating correctly, then the
cause may be damage to the control box or actuator. Please contact your supplier.
Transport
The walker can be transported either in
vertical or in horizontal position. It should
be set in the lowest height position to
save space and facilitate handling. Ensure
that the foot brakes are activated. Be
careful when loading the walker into a
vehicle, giving attention to securing it.
Storage
The walker should be stored indoors and
in an upright position. Do not place heavy
items on top of it while stowed away. The
maximum storage temperature is 50 °C.
The walker must cool down for one hour
at 25 °C before use. The minimum storage
temperature is −20 °C. The walker must
warm up three hours at 25 °C before use.
Different beep signals:
Short "beep...beep" from the con-
trol box every 24th second = low
battery level. Charge the battery.
Long "beeeeep" when the battery is put
in the control box = good connection.
Short "beep...beep" when the walker is
being raised and lowered = low voltage.
The battery should be replaced.
–>
Replace the complete wheel
–>
Adjust the brake cables
–>
Replace the entire back wheel section
–>
Replace the complete brake handle
–>
Replace the brake cable
–>
Charge or replace the battery (see section 7)
–>
See section 7, charging the battery
–>
Check that the battery is clean and correctly mounted
–>
Check that all contacts are properly in place and tightly fitted
–>
Check all cables and replace any damaged one(s)
–>
Replace the switch
–>
Replace the height adjusting panel
Cleaning
The walker can be cleaned with a damp
cloth and mild household detergents.
Fluids should be avoided. Do not use
abrasives, steam- or high-pressure
cleaners. The walker cannot be hosed
because of the electric motor. In case
of multiple patients using the walker, it
is necessary to clean and disinfect the
walker and its accessories before use
by another patient. Remove the battery
from the walker before the disinfection/
cleaning process begins. Allow the walker
to dry in room temperature before use.
Do not store below 0 °C before the walker
is completely dry. Cleaning must be done
manually without mechanical devices
(e.g., ultrasonic cleaner or disinfectant
washer). No further use of products
in the case of water penetration.
–
5
–
TOPRO Taurus E
If recharged, the battery will still give
power but only for a limited time.
Long "beeeeep" when the Taurus is
being raised and lowered = battery
voltage lower than 17.6 V. It will only
be possible to lower it, not raise it.
Short "beep...beep...beep...beep"
means too high temperature inside
the control box. Stop using until the
control box has cooled down.
Disinfection
Disinfect by wiping generally accessible
surfaces with disinfectant. Disinfection
must only be carried out by authorized
personnel and by wearing sufficient pro-
tective equipment. The surface must be
cleaned with a disinfectant that contains
70–80 % ethanol. We advise against disin-
fectant that contains chlorine or phenol.
Running liquids should be avoided. The
battery of the walker must be removed
before the disinfection process take place.
Before use, allow the walker to air-dry in
room temperature until there is no more
superficial moisture on the product. The
manufacturer cannot be held responsible
for any damage or injuries that might occur
using harmful disinfectant or disinfection
carried out by unauthorized personnel.
Art. No. User Manual: 104801 – Revision C, 2022-05
EN
EN
NO
DE
NL
SV
DA
FI
IS
FR
IT
ES
CS
Werbung
