RADEMACHER RolloTube I-line Sun Medium Serie Original - Betriebs- Und Montageanleitung Seite 30

General safety instructions
Danger due to electric shock when working on all electrical systems.
◆ The electrical connection for the tubular motor and all work on the electrical systems
may only be undertaken by an authorised qualified electrician and in accordance with
the connection diagrams in these instructions, see pages 37/38/39.
◆ Always undertake mounting and connection work with the equipment disconnected
from the mains power.
The use of defective equipment can lead to personal injury and damage
to property (electric shocks, short circuiting).
◆ Never use defective or damaged equipment.
◆ Check the drive and mains cable beforehand for damage.
◆ Consult our customer service department (see page 48) in the event that you discover
damage on the equipment.
Potential risk to life and limb resulting from uncontrolled starting of
the drive.
Never attempt to manually stop the motor/awning in the event of uncontrolled move-
ment. In such cases, switch off all power to the drive and take appropriate safety.
precautions to prevent unintentional switching on. Arrange to have the system checked
by a specialist engineer.
Exceeding the maximum permissible running time (KB) may overload
the tubular motor.
◆ The maximum permissible running time for a cycle may not be exceeded when the
equipment is in operation. For this reason, the tubular motor has an automatic
running time limit (KB) of four minutes.
◆ If the running time limit is triggered, then the tubular motor must be left for at
least 20 minutes to cool down.
i
Proper use / operational conditions
Only use the tubular motors for the electrical operation of awnings.
IMPORTANT
Only use the manufacturer's original components and accessories.
Only use tubular motors which correspond to the local conditions in
terms of their output. Incorrectly dimensioned tubular motors can lead
to damage.
◆ An insufficiently dimensioned tubular motor can be damaged due
to overloading.
◆ An excessively dimensioned tubular motor can cause damage, for
example, to the roller shutters and roller shutter casing when
configuring the automatic end-point setting.
Consult a specialist dealer when selecting the tubular motor and observe our tractive
force specifications on our Website: www.rademacher.de
i
Incorrect use
Using the tubular motor for purposes other than those stated above is
considered incorrect use.
30
Incorrect use leads to an increased risk of injury.
◆ Train all personnel to safely use the tubular motor.
◆ Do not allow children to play with the fixed control units.
◆ This device may be used by children from 8 years of age upwards as well as by
persons with reduced physical, sensory or mental capacities or with lack of experience
and knowledge if they are supervised or have been instructed on how to use the
device safely and if they understand what dangers may resulted from this.
◆ Cleaning and user maintenance may not be carried out by children without supervision.
◆ Watch the moving awning and keep other people away from the area until the
movement has completed.
For awning systems which can be operated out of sight of the operator:
◆ Awnings may not be operated if work is being carried out nearby (e.g. windows
being cleaned).
For automatically actuated awnings:
◆ Awnings must be disconnected from the power supply if work is being carried out
nearby.
Regular maintenance of awnings increases operational reliability.
◆ Check the awnings regularly for poor balance or damaged lines and springs.
◆ Have damaged awnings repaired by a specialist firm.
Contact with the drive housing can cause burns.
◆ The tubular motor gets hot during operation. Allow the motor to cool down prior to
undertaking any further work on the motor.
◆ Never touch the hot drive housing.
Mortal danger in the event of operation without configured end points.
◆ The end points must be configured in order to ensure safe operation. In order to do
so, please refer to the corresponding chapter in this manual provided on page 41.
Operating conditions
◆ A continuous 230 V / 50 Hz power supply must be available at the site of installation
for the electrical connection in combination with on-site switchgear (fusing).
EN