Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Hot tub
- The spas of the "Professional" range can also be installed with
the tub edge flush with the floor. Refer to the drilling template
shown in
5.
In any case, keep in mind that the spa-pack and the balance tank
must be placed at a lower level (
retainer tub, they can remain on the same level as the hot tub.
N.B. Since the sizes may vary slightly, always check the measure-
ments before installing the hot tub.
- Make sure that the plumbing under the tub is accessible, for ex-
ample, by preparing a passage (
perimeter that is sufficiently wide (about 80 cm) to make opera-
tions easy. This passage can be closed using removable under-
frames (detail 3), with suitable supports (detail 4). Drainage for
any water stagnation must also be provided (detail 5).
- If it is to be floor-installed, it will be necessary to fill in the outer
perimeter of the tub, using removable panels all along the pe-
rimeter.
- In any case, you will require a support base below the tub bot-
tom (in concrete, steel beams,
the metal supports provided to support the tub edge, posi-
tioned as shown in detail 6. The realization of the support base
must take into account the position of the support feet (
and the load of the spa, taking into account the table "Weights"
shown above.
- Study the routes and dig any necessary holes and channels for
the water and electric connections for the spa and the Spa-pack,
with the balance tank and the ground drainage points, taking
into account that:
the plumbing pipes are those shown in
placed so as to avoid siphons. This does not apply to the blower,
which does require a blower (
buttons (
2-2a, det. 2) are supplied that should be installed
near the spa, and that will be connected to a specific box (supplied
with the spa-pack, it can be wall-mounted or installed under the
tub,
2-2a, det. 2a). This box must then be connected to the
electrical box on the spa-pack by means of a multi-polar normal-
ized cable 6x0.75 mm
2
.
the spotlight box of the spa (located under the tub) must be con-
nected to the electrical box on the spa-pack by means of a normal-
ized bi-polar cable 2x1.5 mm
A cable track must also be provided for electrical connections
from the balance tank to the electric wiring box on the Spa-pack
(8 standard leads, with a minimum section of 1.5 mm
Spa-pack "booster kit": in the instance where a spa-pack
"booster kit" is also installed, a separate supply line must be pro-
vided and it must be connected to the main spa-pack; refer to the
relative documentation.
Spa-pack / Spa pak "booster kit"
- For correct spa-pack operation, comply with the dimen-
Jacuzzi Europe S.p.A. © 2023
6). In the case of a lowered
5, detail 2) around the outer
5, detail 1), while you can use
2-2a which must be
2-2a e 6, det. B).
2
.
2
).
sions provided in the respective table
the shorter the hoses are, the smaller the loss of load will be. We
recommend that you avoid bends, as far as possible, (we suggest
you use flexible PVC hoses).
In the instance where the main spa-pack has a heat exchanger
for heating water, it is necessary to connect the primary circuit
to the system which supplies hot water, in addition to connect-
ing the electrical box with devices (solenoid valve, motor pump)
that control the recirculation of the hot water in the exchanger's
primary circuit.
Water connections for the Spa-pack must also include the con-
nection between the filter and a ground drainage point.
- Spa-pack must always be installed in a ventilated indoor
area, which is not accessible to persons without a key or
tools and it must be protected from water and bad weather
(see note "Spa-pack and the balance tank" in the previous chapter).
For perfect operation of the system, the Spa-pack must be in-
stalled at the same level as the balance tank (
minimal difference.
The balance tank
- When possible, it must be installed near the Hot tub for opti-
mum efficiency (excess water will fall into the balance tank).
1)
For correct operation of the balance tank, comply with the
dimensions provided in the respective tables (
- If the balance tank is installed outside, a suitable system
must be provided to protect it against the sun's rays and ul-
traviolet radiation, to prevent damaging the container.
Preparing the plumbing connections
The plumbing system (including connectors, gate valves, etc.,
2-2a) for connecting the Hot tub to the Spa-pack and the
balance tank, must be set up by the installer.
The Customer must provide the ground drainage points (
2-2a, detail 27 and 28) of suitable dimensions, which can be
inspected for any cleaning, and to which the low-point drain ø
50 mm (
2-2a, detail 3), the loading/overflow of the balance
tank and the drain from the filter are to be connected.
Spa-pack "booster kit": in the instance where a spa-pack "boost-
er kit" is also installed, it must be connected to the drainage system;
refer to the relative documentation.
CAUTION! Before preparing the ground drainage
points, consult the local authority for the regulations
that control the drainage of chemically treated water.
In particularly cold areas, to avoid the risk of any remaining
water freezing (water that may remain in plumbing after empty-
ing the system) it is advisable to install valves for the complete
drainage of plumbing (
21
6: this is because
6) or with a
2-2a, detail 31).
Jacuzzi Europe S.p.A. © 2023
6).
Werbung
