Jacuzzi PROFESSIONAL Serie Vorinstallationsblatt Seite 19

En
It is the installer/owner's responsibility to check and
ensure compliance with the specific local regulations prior
to installation. Jacuzzi Europe S.p.A. gives no guarantee in
this respect and declines all responsibility for the compli-
ance of the installation carried out.
Technical specifications
Sienna Experience ( 1) includes:
- the spa-pack control unit (det. A,
Note: a booster-kit spa-pack (optional, det. B,
stalled and connected to the one supplied as standard; please see
the relative documentation.
- the balance tank ( 1, det. V/V1) which, once connected, is
required to hold water that overflows when users get into the
tub. Its nominal capacity is 1,000 litres (operating with about
800-850 litres).
- the hot tub is to be connected, with hoses, to the spa-pack, the
balance tank and the drain.
MAXIMUM POWER ABSORPTION OF SYSTEM
(k): at 230 V - (j): absorbed power
(x): see the "Preparing the electrical connections" chapter
(*): special standard (not valid for Europe)
- three-phase version (with heater)
Power supply (x)
Volts Hertz Ampere (k)
220 - 240 3~ (*) 50/60
380 - 415 3N~ 50/60
- three-phase version (with exchanger)
Power supply (x)
Volt Hertz Ampere (k)
220 - 240 3~ 50/60
(*)
380 - 415 3N~ 50/60
- single-phase version (with heater)
Power supply (x)
Volt Hertz Ampere (k)
220 - 240 50/60
- single-phase version (with exchanger)
Power supply (x)
Volt Hertz Ampere (k)
220 - 240 50/60
Jacuzzi Europe S.p.A. © 2023
1).
1) can be in-
Spa-pack A Spa-pack B
consumption consumption (optional)
kW Ampere (k)
45 17
(k) (j)
3,5
(j)
26 17
(k) (j)
Spa-pack A Spa-pack B
consumption consumption (optional)
kW Ampere (k)
13 5
(k) (j)
3,5
8 5 (j)
(k) (j)
Spa-pack A Spa-pack B
consumption consumption (optional)
kW Ampere (k)
25,5 5,75 3,5
(k) (j) (j)
Spa-pack A Spa-pack B
consumption consumption (optional)
kW Ampere (k)
19,5 4,25 3,5
(k) (j) (j)
The electrical system that powers the hot tub must be sized for
maximum consumption (as shown in the relevant tables).
HEAT EXCHANGER
- MAX primary inlet temperature .................................................... 50 °C
- Connections ............................................................................................ 3/4"
- Primary circuit flow rate .............................................................. 38 l/min
- Primary pressure drop ............................................................0.271 m H
WEIGHT
- spa
Net
Average volume
weight
of use
kg litres
~ 200 ~ 1430
- spa-pack A
max weight
at full load
kg
~ 285
- spa-pack B ("booster kit", optional)
max weight
at full load
kg
~ 140
- balance tank V
max weight
at full load
kg
~ 925
kW
- balance tank V1 (lowered)
max weight
0,7
at full load
(j)
kg
~ 900
kW
0,7
Components
(j)
The components and connections you need to build the sys-
tem are listed below (see
Hot tub and plumbing
kW
1 overflow channel with grid
0,7
2 buttons
(j)
box for connection of buttons
2a
low-point drain with gate valve
3
4A1+4B1 to the balance tank (overflow lines)
4A2+4B2 to the balance tank (overflow lines)
kW
4C1/4C2 from the overflow channel (overflow lines)
0,7
hydromassage pump suction lines
5
(j)
hydromassage pump delivery lines
6
19
MAX Max.
Resting
water volume total weight surface
litres kg m
~ 1760 ~ 1960 ~ 0,95
resting
surface
m 2
~ 1,1
resting
surface
m 2
~ 0,5
resting
surface
2
m
~ 1,2
resting
surface
m 2
~ 1,8
2-2a).
Jacuzzi Europe S.p.A. © 2023
O
2
Load on rest-
ing surface
2 2
kg/m
~ 2063
ground
load
kg/m 2
~ 260
ground
load
litres
~ 280
ground
load
2
kg/ m
~ 770
ground
load
kg/ m 2
~ 500