Inhaltsverzeichnis
Werbung
STAND SPARE PARTS LIST
REF. NR.
DESCRIPTION
1
TOP STIFFENER L / R SIDE
2
M5 NYLON NUT
3
M5 HEX BOLT
4
FRAME CLIP
5
FRAME BRACKET
6
TOP STIFFENER (FRONT / REAR)
7
COACH BOLT M8
8
Ø 8 WASHER
9
M5 MYLON NUT
10
LEG NO.1
11
LEG
12
FEET PAD
13
BOTTOM STIFFENER L / R SIDE
14
BOTTOM STIFFENER (FRONT / REAR)
15
M6 HEX-HEAD BOLT
16
Ø 6 WASHER
17
M6 NYLON NUT
18
M5 NUT
19
RING HOOK
20
FRAME TUBA
78
Q'TY
2
RADIAL TILE CUTTER
12
12
THE NUMBERS IN THE FOLLOWING TEXT
CORRESPOND WITH THE PICTURES AT PAGE 2
4
4
TECNICAL SPECIFICATIONS
2
16
Motor
Power
16
No load speed
16
Blade speed
2
Blade size
2
Max. depth of 90° cut
4
Max. depth of 45° cut
Max. cutting length
2
Netto weight
2
Lpa (Sound pressure level)
4
Lwa (Sound power level)
Vibration
8
4
PRODUCT INFORMATION
2
Fig.4
1
1 Scale plate
2 Tighten knob
1
3 Indicater
4 Grip handle
5 Guide rall
6 Fixing bolt / mitre gauge
7 Knob / mitre gauge
8 Mitre fence
9 Blade guard
10 Back Fence ( central end with 45° cutting)
11 Back Fence (double end planed)
12 Locking knob (for stop head moving)
FUNCTIONS AND CHARACTERISTIC
Blade can tilt to any angle between 0° and 45°.
The mitre gauge on the table can turn to any angle.
In the process of cutting, the pump can provide blade
with water. This can increase the life of the blade and also
decrease dust.
Blade moves along the guide rail in straigh and keeps the
cut stable
Ferm
Ferm
SAFETY INSTRUCTIONS
The following symbols are used throughout this manual:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of
the instructions in this manual.
Denotes risk of electric shock.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
| 230 V~, 50 Hz
how to operate it. Maintain the machine in accordance
| 550 W
with the instructions to make sure it functions properly.
| 2950/ min
Keep this manual and the enclosed documentation with
| 28 m/s
the machine.
| Ø 180 mm,
| Ø25.4mm Bore
1. Keep work area clean.
| 25 mm
Cluttered areas and benches invite injuries.
| 15 mm
2. Consider work area environment.
| 330 mm
Don't expose power tools to rain. Don't use power
| 21.8 kg
tools in damp or wet locations. Keep work area well
| 59.4 dB(A)
lit. Don't use power tools in presence of flammable
| 72.4 dB(A)
liquids or gases.
| 2.8 m/s
2
3. Guard against electric shock.
Prevent body contact with grounded surfaces (e.g.
pipes, radiators, ranges refrigerators).
4. Keep children away.
Do not let visitors contact tool or extension cord.
All visitors should be kept away from work area.
5. Store idle tools.
When not is use, tools should be stored in dry, high,
or locked-up place, out of reach of children.
6. Don't force tool.
It will do the job better and safer at the rate for which
it was intended.
7. Use right tool.
Don't force small tools or attachments to do the job
of heavy duty tool. Don't use tools for purposes not
intended:for exam-ple, don't use a circular saw for
cutting tree limbs or logs.
8. Dress properly.
Do not wear loose clothing or jewelry. They can be
caught in moving parts. Rubber gloves and nonskid
footwear are recommended when working
outdoors. Wear protective hair covering to contain
long hair.
9. Use safety glasses.
Also use face or dust mask if cutting operation is
dusty.
10.Don't abuse cord.
Never carry tool by cord or yank it to disconnect it
from receptacle. Keep cord from heat, oil and sharp
edges.
11.Secure work.
Use clamps or a vise to hold work. It's safer than
using your hand and it frees both hands to operate
tool.
12.Don't overreach.
Keep proper footing and balance at all times.
3
Werbung
Inhaltsverzeichnis
