Inhaltsverzeichnis
Werbung
13.Maintain tools with care.
Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and
changing accessories. Inspect tool cords periodically
and, if damaged, have repaired by authorized service
facility. Inspect extension cords periodically and
replace if damaged. Keep handles dry, clean and free
from oil and grease.
14.Disconnect tools.
When not in use, before servicing, and when
changing accessories such as blades, bits and cutters.
15.Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
16.Avoid unintentional starting.
Don't carry plugged-in tools with finger on switch.
Be sure switch is off when plugging in.
17.Outdoor use extension cords.
When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
18.Stay alert.
Watch what you are doing. Use common sense. Do
not operate tool when you are tired.
19.Check damaged parts.
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
determine that it will operate properly and perform
its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect
its operation. A guard or other part that is damaged
should be properly repaired or replaced by an
authorized service center unless otherwise
indicated elsewhere in this instructions manual.
Have defective switches replaced by an authorized
center. Do not use tool if switch does not turn it on
and off.
20.Warning.
The use of any other accessory or attachment other
than recommended in this operation instructions or
the catalog may present a risk of personal injury.
21.Have your tool repaired by an expert.
This electric appliance is in accordance with the
relevant safety rules repairing of electric apliances
may be carried out only by experts otherwise it may
cause considerable danger for the user.
22.Connect the dust extraction device.
Whenever there are facilities for fitting a dust
extraction system, make sure it is connected and
used.
ADDITIONAL SAFETY RULES FOR TILE
CUTTERS
•
Wear protective glasses, dust mask, ear defenders,
work gloves and protective-sliding shoes.
•
Keep the table flat an d do not scratch or press the
table.
•
Do not put hands anywhere near the blade whilst it is
rotating.
•
Do not attempt to free a jammed blade without first
switching off or removing the plug from the mains
power supply.
•
Do not cut small workpiece and also do not use for a
purpose not intended.
4
•
Keep water full in the tank when you operate the
cutter.
•
Do noy use any solvents for instead water in this tool.
•
Maintain th tool with care, keep blade sharp and
clean, inspect plug, cord and water hose periodically.
•
Disconnect the tool from power source when not in
use or before servicing. Changing the accessories
must be carried out by qualified person.
•
Ensure to locked tool head (Fig.5), before storing it.
•
When not in use, the tool must be stored in a dry
place.
ELECTRICAL SAFETY
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions. Keep these
instructions in a safe place!
Always check that the voltage corresponds to the
voltage on the rating plate.
Replacing cables or plugs
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm
2
. When using a cable reel always unwind
the reel completely.
REF. NR.
44
45-47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
Ferm
Ferm
TILE CUTTER SPARE PARTS LIST II
DESCRIPTION
MOTOR
CABLE ANCHOR ASSEMBLY
CABLE SLEEVE
RUBBER WASHER
SWITCH
CONNECTION BOX
EARTH MARK
CONNECTING BOARD
ST3,5X16 SELF-DRIVING SCREW
RUBBER WASHER FOR SOURCE POWER BOX
COVER FOR SOURCE POWER BOX
ST2,9X18 SELF-DRIVING SCREW
M5X15 ROUND-HEAD SCREW
CAPACITOR
ST3,5X12 SELF-DRIVING SCREW
CAPACITOR CLIP
M5X15 ROUND-HEAD SCREW
ANCHOR
ST2,9X18 SELF-HEAD SCREW
TERMINAL
PUMP
SCREW
WASHER
PROTECTIVE-WATER BOARD
WASHER
NUT
PLUG
M8 NYLON LOCKED SCREW NUT
Ø 8 FLAT WASHER
CORD TUBE
Ø 180 BLADE
WATER TANK
PC
1
1
1
1
1
1
1
1
2
1
1
4
4
1
1
1
1
1
2
1
1
1
1
1
1
1
1
4
4
1
1
1
77
Werbung
Inhaltsverzeichnis
