Inhaltsverzeichnis
Werbung
TILE CUTTER SPARE PARTS LIST I
REF. NR.
DESCRIPTION
1
M6X12 HEX-SCREW
2
BASE FOR FENCE
3
SLIDING SCREW
4
ANGLE PLATE
5
PROTECTIVE-DUST COVER
6
SPACER
7
PLASTIC WASHER
8
KNOB / MITE
9
FENCE
10
M6X25 HEX-SHREW
11
TABLE (RIGHT)
12
TABLE (LEFT)
13
SUPPORT PLATE (FRONT / BACK)
14
M5X20 HEAD-SUNK SCREW
15
M6X20 HEX-SCREW
16
Ø 6 WASHER
17
ANGLE PLATE (FRONT / BACK)
18
ARROW HEAD
19
LOCKING KNOB
20
M6X18 FLANGE SIDE SCREW
21
ANGLE PLATE (FRONT / BACK)
22
M4X12 SCREW
23
PROTECTIVE GUARD
24
LEFT SPIRAL SCREW NUT
25
OUITSIDE FLANGE
26
GUIDE RAIL
27
INSIDE FLANGE
28
M6X15 HEX-SCREW
29
Ø 6 FLAT WASHER
30
Ø 6 SPRING WASHER
31
FIXING PROTECTIVE GUARD
32
M5X12 HEX-SCREW
33
Ø 5 FLAT WASHER
34
Ø 5 SPRING WASHER
35
BASE
36
LIMITING LUMP
37
PREJUDICIAL ARBOR
38
609ZZ BEARING WITH PROTECTIVE-DUST COVER
39
Ø 9 WASHER FOR ARBOR
40
HANDLE
41
M5X15 ROUND-HEAD SCREW
42
Ø 5 FLAT WASHER
43
Ø 5 SPRING WASHER
76
INSTALLATION
ASSEMBLY
PC
2
1
are completed and tou haven read and understood the safety
1
and operational instructions.
1
Installing the stand
1
Fig.1 - 3
•
Note to find the leg No. 10 and top stiffener No. 6,
1
there were special marked as Fig.3 shown, to install
1
the stand.
1
•
Install the tank frame on the top stiffener No.1, when
stand complete assembled. (Fig.3)
2
•
Note to tighten firmly all the bolts and nuts, for
4
holding whole machine secure.
1
Installing the Tile Cutter
1
Fig.4
1 / 1
•
Install back fence No.10 and No.11 as Fig.4, and note
to position the fence No.10 in right side, that can
16
assist blade for tilt cutting.
2
•
Locate both assembled tool (Fig.4) onto stand
2
(Fig.3), as Fig.6 shown.
•
Refer the illustration Fig.7 to install the hose and
1 / 1
power cord of coolant pump into ring-hook No.19.
2
(Fig.1)
2
CONNECTING TO THE POWER SUPPLY
6
Check that the power supply and plug used in
1 / 1
accordance with tour tool. Have a look at the rating plate
on the tile cutter. Any changes should always be carried
3
out by a qualified electrician.
1
1
1
1
If not properly earthed this machine can cause an
1
electrical shock. Be sure that the power supply outlet is
earthed. If there is any doubt, have it checked by a
3
qualified electrician.
3
3
1
the power supply outlet. Contact will cause a severe electrical
4
shock.
4
Using an extension lead
4
The use of any extension lead will cause some loss of
1
power. To keep this to a minimum and to prevent
overheating and motor burn-out, ask advice from a
2
qualified electrician to determine the minimum wire size
4
of the extension lead.
4
The extension lead should be equipped with an earthed
4
type plug that fits the power supply outlet at one end,
1
and with an earthed type socket that fits the plug of the
machine at the other end.
2
2
2
Ferm
Ferm
Warning! Never connect the plug to power
source outlet until all installations and adlustments
Warning! This machine must be earthed.
Warning! Avoid contact with the terminals on the
plug when installing (removing) the plug to (from)
OPERATING THE TOOL
Read and understand the following items about
your tile cutter before attempting to use the
machine.
Fig.4 - 5
•
Adjust the required tool position, then tighten all the
adjusting knobs No.2, fence bolts and mitre gauge
bolts.
•
Release the locked knob No.13. (Fig.4 and 5)
•
Turn on the main switch and allow your tool to reach
the maximum speed before commencing cutting.
•
Hold the workpiece firmly against the work table and
fence, then feed machine smoothly and evently to the
workpiece.
•
Cutting actions tends to slow the blade down.
Pressure should therefore be occasionally released
to allow the blade to regain the full speed.
Warning! Do not attempt topick up an off-cut or
to remove the holding workpiece before the cutting
blade has completely stopped. If holding the workpiece by
hand take extreme care and ensure hand is kept away from
the cutting blade.
CHANGING CUTTING BLADE
Fig.4, 8 - 9
Warning! To avoid injury from accidental starting,
always turn the switch off "0" and remove the
power plug from the power source before changing the blade.
•
Remove the protective guard No.9. (Fig .4)
•
Use specific spanners to release the (left-spiral)
screw nut No.1. (Fig.8)
•
Remove the outside flange No.2, then the blade
No.3. (Fig.8)
•
Care to assemble the new blade, the head of arrow
on the blade and protecting guard No.9 (Fig.4) must
be in the same direction.
•
Assembling the outside flange, then lighten the screw
nut firmly. (Fig.8)
Note:
•
Inspect the new blade for cracks or other visible
damage. Discard it if such damage is found.
•
Position a smaller spanner in the shaft, then tighten
the nut firmly with a bigger spanner.
5
Werbung
Inhaltsverzeichnis
