Transport (Fig. 1, 2); Maintenance; Storage; Electrical Connection - Scheppach HM90SL Bedienungsanleitung

• Important! The cutting angle of the teeth, in oth-
er words the direction of rotation of the saw blade
(6) must coincide with the direction of the arrow on
the housing.
• Before continuing your work make sure that all safe-
ty devices are in good working condition.
• Important! Every time that you change the saw
blade (6), check to see that it spins freely in the
table insert (10) in both perpendicular and 45° an-
gle settings.
• Important! The work to change and align the saw
blade (6) must be carried out correctly.
8.11 Using the laser & LED - light (Fig. 2, 3)
• To switch on: Press the on / off switch for laser
& LED (28) 1x to switch on the laser. Press 2x to
switch on the LED light.
• To switch off: Move the ON/OFF switch of the laser
& LED (28) 3 times.
8.12 Adjusting the laser (Fig. 3)
If the laser (8) ceases to indicate the correct cutting
line, you can readjust the laser. To do so, open the
screws (g) and set the laser by moving sideways to that
the laser beam strikes the teeth of the saw blade (6).
9.

Transport (Fig. 1, 2)

• Tighten the set screw (9) in order to lock the rota-
ry table (17)
• Activate the release lever (3), press the machine
head (4) downwards and secure with the safety pin
(32). The saw is now locked in its bottom position.
• Fix the saw's drag function with the locking screw
for drag guide (20) in rear position.
• Carry the equipment by the fixed saw table (18).
• When reassembling the equipment proceed as de-
scribed under section 7.

10. Maintenance

m Warning! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to time
using a cloth. In order to extend the service life of
the tool, oil the rotary parts once monthly. Do not oil
the motor.
When cleaning the plastic do not use corrosive prod-
ucts.
34 | GB
Brush inspection
Check the 2 carbon brushes (42) after the first 50 oper-
ating hours with a new machine, or when new brushes
have been fitted. After carrying out the first check, re-
peat the check every 10 operating hours.
If the carbon is worn to a length of 6 mm, or if the
spring or contact wire are burned or damaged, it is
necessary to replace both brushes. If the brushes are
found to be usable following removal, it is possible to
reinstall them.
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consum-
ables.
Wear parts*: Carbon brush, saw blade, table inserts,
dust bags
* Not necessarily included in the scope of delivery!

11. Storage

Store the device and its accessories in a dark, dry and
frost-proof place that is inaccessible to children. The
optimum storage temperature is between 5 and 30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust
and moisture.
Store the operating manual with the electrical tool.

12. Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions.
The customer's mains connection as well as the
extension cable used must also comply with these
regulations.
Important information
In the event of an overloading the motor will switch
itself off. After a cool-down period (time varies) the
motor can be switched back on again.
Damaged electrical connection cable
The insulation on electrical connection cables is of-
ten damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
www.scheppach.com