Scheppach HM90SL Bedienungsanleitung Seite 33

8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1, 2, 15)
The crosscut saw can be used to make mitre cuts of
0° - 45° in relation to the work face.
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (10a) must be fixed at the out-
er position.
• Open the set screw (10b) for the adjustable stop
rail (10a) and push the adjustable stop rail (10a)
outwards.
• The adjustable stop rail (10a) must be fixed far
enough in front of the innermost position that the
distance between the moveable stop rail (10a) and
the saw blade (6) amounts to a maximum of 8 mm.
• Before making a cut, check that the moveable stop
rail (10a) and the saw blade (6) cannot collide.
• Secure the set screw (10b) again.
• Move the machine head (4) to the top position.
• Fix the rotary table (17) in the 0° position.
• Loosen the locking lever (22) and use the handle (1)
to angle the machine head (4) to the left, until the
pointer (26) indicates the desired angle measure-
ment on the scale (27).
• Re-tighten the locking lever (22).
• Cut as described in section 8.3.
8.7 Mitre cut 0°- 45° and turntable 0°- 45°
(Fig. 2, 15)
The crosscut saw can be used to make mitre cuts to
the left of 0°- 45° in relation to the work face and, at the
same time, 0° - 45° to the left or 0° - 45° to the right in
relation to the stop rail (double mitre cut).
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (10a) must be fixed at the out-
er position.
• Open the set screw (10b) for the adjustable stop
rail (10a) and push the adjustable stop rail (10a)
outwards.
• The adjustable stop rail (10a) must be fixed far
enough in front of the innermost position that the
distance between the moveable stop rail (10a) and
the saw blade (6) amounts to a maximum of 8 mm.
• Before making a cut, check that the adjustable stop
rail (10a) and the saw blade (6) cannot collide.
• Secure the set screw (10b) again.
• Move the machine head (4) to its upper position.
• Release the rotary table (17) by loosening the set
screw (9).
• Using the handle (14a), set the rotary table (17) to
the desired angle (refer also to point 8.4 in this re-
gard).
• Re-tighten the set screw (9) in order to secure the
rotary table.
• Undo the locking lever (22)
• Use the handle (1) to tilt the machine head (4) to the
left until it coincides with the required angle value
(in this connection see also section 8.6).
• Re-tighten the locking lever (22).
• Cut as described under section 8.3.
8.8 Limiting the cutting depth (Fig. 3, 16)
• The cutting depth can be infinitely adjusted using
the screw (30). To do this loosen the knurled nut
(30a) on the screw (30). Turn the screw (30) in or
out to set the required cutting depth. Then re-tighten
the knurled nut (30a) on the screw (30).
• Check the setting by completing a test cut.
8.9 Sawdust bag (Fig. 1/20)
The saw is equipped with a debris bag (21) for saw-
dust and chips.
Attach the dust bag (21) to the outlet opening (21a).
The debris bag (17) can be emptied by means of a
zipper at the bottom.
8.10 Changing the saw blade (Fig. 1, 2, 17, 18)
Remove the power plug!
Important! Wear safety gloves when changing the
saw blade. Risk of injury!
• Swing the machine head (4) upwards and lock with
the safety pin (32).
• Loosen the Philips screw (e) two turns.
• Press the unlocking lever (3). Fold the saw blade
guard (5) up sufficiently that the flange screw (34)
is free.
• Firmly press the saw shaft lock (33) and slowly ro-
tate the flange bolt (34) in clockwise direction. The
saw shaft lock (33) engages after no more than one
rotation.
Attention! When loosening the screw, the machine
head lowers slightly.
• Now, using a little more force, slacken the flange
bolt (34) in the clockwise direction.
• Turn the flange screw (34) right out and remove the
external flange.
• Take the blade (6) off the inner flange and pull out
downwards.
• Carefully clean the flange screw (34), outer flange
and inner flange.
• Fit and fasten the new saw blade (6) in reverse or-
der.
www.scheppach.com GB | 33