Associated Equipment; Maintenance And Storage; Periodic Inspection - Tractel HT Access Installations-, Gebrauchs- Und Wartungsanleitung

15. Lateral attachment element.
16. Service ring.
17. Sternal fall arrest indicator.
18. Dorsal fall arrest indicator.
EN
7.2. Designation of attachment points
References used in the HT harnesses to designate the
different attachment points:
• A: the marking "A" on attachment points designates
them for fall arrest systems.
• A/2: the marking "A/2" on the attachment points
designates them for fall arrest systems to be coupled
symmetrically to each other with an EN 362 connector
to make one single attachment point.
• M: designates an attachment point for securing at the
workstation (EN 358).
• S: designates a suspension attachment point for work
on tensioned rope (EN 813).
7.3. Materials
• Strap + sewing thread: polyester.
• Buckles made of galvanized steel or cataphoresis and
aluminium coating.
• Foam back support covered with cordura.
• Backplate, loops:
elastomer.

8. Associated equipment

An EN 363 fall arrest system consists of the following
elements:
• An anchorage (EN 795).
• An end connector (EN 362).
• A fall-arrest device (EN 353-1/2-EN 355-EN 360).
• A connector (EN 362).
• A fall-arrest harness (EN 361).
All other associations are forbidden.
An EN 361 fall arrester harness is the only
body-gripping device authorised for use in a
fall prevention system.

9. Maintenance and storage

This equipment, must be stored in a dry place at a
temperature between -30°C and +50°C.
During transport and storage, protect the equipment
against all possible damage (cutting edges, direct eat
sources, chemical products, U.V., etc.).
14
polyethylene, thermoplastic
DANGER
10. Equipment compliance
TRACTEL SAS RD 619 – Saint-Hilaire-sous-Romilly
F-10102 Romilly-sur-Seine France hereby declares
that the safety equipment described in this manual.
1) EU regulation:
• complies with the requirements of European regulation
UE 2016/425 of March 2016.
• is identical to the PPE, having been subject to the
"UE"-type-examination certificate issued by notifed
boby APAVE Exploitation France SAS (n°0082) – 6
Rue du Général Audran – 92412 COURBEVOIE
cedex – France, identified under the number 0082,
and tested according to the EN 361/2002, EN
358/2018 and EN 813/2008 standards.
• is subject to the procedure referred to in Annex VIII
of the EU Regulation 2016/425 of the European
Parliament, Module D, under the control of a notified
body: APAVE Exploitation France SAS (n°0082) – 6
Rue du Général Audran – 92412 COURBEVOIE
cedex – France, identified under the number 0082.
2) UKCA regulation:
PPE regulation 2016/425 as amended to apply in Great
Britain.
11. Marking
The marking on each product indicates:
a: the trade name: Tractel
b: the name of this equipment.
c: the referenced standard.
d: this equipment reference.
e: CE Lo go followed by the number 0082,
identification number of the approved body
responsible for production control.
f: Year and month of manufacture.
g: the serial number.
h: a picto gram showing that the manual mustbe
read before use.
w: Maximum operating load.
ai: Size range in cm.
ax: R: for work positionning only.
: UKCA compliant.

12. Periodic inspection

An annual periodic inspection is required, but depending
on the frequency of use, environmental conditions
and regulations of the company or the country of use,
periodic inspections may be more frequent.
Periodic inspections should be carried out by an
authorised and competent technician, in compliance
with the manufacturer's instructions transcribed in the
file "Tractel PPE inspection instructions".
®
.
®