Service Information; Transport; Storage - Scheppach 5901222901 Original Bedienungsanleitung

10.4 Brush inspection
Check the carbon brushes after the first 50 operating
hours with a new machine, or when new brushes have
been fitted. After carrying out the first check, repeat
the check every 10 operating hours.
If the carbon is worn to a length of 6 mm, or if the
spring or contact wire are burned or damaged, it is
necessary to replace both brushes. If the brushes are
found to be usable following removal, it is possible to
reinstall them.
When servicing the carbon brushes, open the two
latches counterclockwise (as shown in Figure 21).
Then remove the carbon brushes.
Replace the carbon brushes in the reverse order.
10.5 Changing the saw blade (fig. 1/2/14-17)
Remove the power plug!
Important!
Wear safety gloves when changing the saw blade.
Risk of injury!
• Swing the machine head (4) upwards and lock with
the locking bolt (23).
• Loosen the retaining screw (5a) of the cover using a
Phillips screwdriver (fig. 14).
WARNING!
Do not fully remove this screw.
• Fold the saw blade guard (5) upwards until the saw
blade guard (5) is above the flange screw (28).
• With one hand insert the Allen key (C) in the flange
screw (28).
• Hold the Allen key (C) and slowly close the saw
blade guard (5) until it touches the Allen key (C).
• Firmly press the saw shaft lock (30) and slowly ro-
tate the flange screw (28) in clockwise direction.
The saw shaft lock (30) engages after no more than
one rotation.
• Now, using a little more force, slacken the flange
screw (28) in the clockwise direction.
• Turn the flange screw (28) right out and remove the
outer flange (29).
• Take the blade (6) off the inner flange (31) and pull
out downwards.
• Carefully clean the flange screw (28), outer flange
(29) and inner flange (31).
• Fit and fasten the new saw blade (6) in reverse or-
der.
• Fold the saw blade guard (5) downwards until the
saw blade guard (5) engages in the locking screw
(5a).
• Re-tighten the locking screw (5a).
• Important!
The cutting angle of the teeth, in other words the
direction of rotation of the saw blade (6) must coin-
cide with the direction of the arrow on the housing.
• Before continuing your work make sure that all safe-
ty devices are in good working condition.
• Important!
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Every time that you change the saw blade (6), check
to see that it spins freely in the table insert (10) in
both perpendicular and 45° angle settings.
• Important!
The work to change and align the saw blade (6)
must be carried out correctly.
10.6 Adjusting the laser (fig. 19-20)
If the laser (32) ceases to indicate the correct cutting
line, you can readjust the laser. To do so, open the
screws (32b) and remove the front cover (32a). Loos-
en the Phillips head screws (E). Set the laser by mov-
ing sideways until the laser beam strikes the teeth of
the saw blade (6).
After adjusting and tightening the laser, mount the
front cover by tightening both screws (32b) by hand.
The machine must be connected to the mains in order
to adjust the laser.
Attention!
Never press the ON/OFF switch (2) when adjusting
the laser. Danger of injury!

10.7 Service information

Please note that the following parts of this product are
subject to normal or natural wear and that the follow-
ing parts are therefore also required for use as con-
sumables.
Wear parts*: carbon brushes, saw blade, table insert
(art. no. 5901215010), saw dust bag
* Not necessarily included in the scope of delivery!

11. Transport

• Tighten the handle (11) to lock the rotary table.
• Press the machine head (4) downwards and secure
with the locking bolt (23).
• Fix the saw's drag function with the locking screw
for drag guide (20) in rear position.
• Carry the equipment by the fixed saw table (15).
• When reassembling the equipment proceed as de-
scribed under section 8 and 9.

12. Storage

Store the device and its accessories in a dark, dry and
frost-proof place that is inaccessible to children. The
optimum storage temperature is between 5 and 30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust
and moisture.
Store the operating manual with the electrical tool.
GB | 33