Cutting Depth Adjustment - Makita UP100D Betriebsanleitung

Switching the shear blade angle
T h e o p e n i n g a n g l e o f t h e s h e a r b l a d e s c a n b e s e t i n t w o
l e v e l s . Y o u c a n s w i t c h t h e o p e n i n g a n g l e b e t w e e n f u l l y
o p e n a n d h a l f - o p e n a c c o r d i n g t o t h e b r a n c h e s t o b e c u t .
Fig.6: 1. F u l l y o p e n 2. H a l f - o p e n
T o s w i t c h t h e o p e n i n g a n g l e , f o l l o w t h e s t e p s b e l o w .
1. T u r n o n t h e t o o l a n d p u l l t h e s w i t c h t r i g g e r t w i c e t o
o p e n t h e s h e a r b l a d e s .
2. W h i l e p u l l i n g t h e s w i t c h t r i g g e r f u l l y , p r e s s a n d
hold the angle adjustment button until the green indica-
t o r l a m p b l i n k s t w i c e .

Cutting depth adjustment

After grinding or replacing the shear blade, adjust the cutting
depth. To adjust the cutting depth, follow the steps below.
1. T u r n o n t h e t o o l a n d p u l l t h e s w i t c h t r i g g e r t w i c e t o
o p e n t h e s h e a r b l a d e s .
2.
W h i l e p u l l i n g t h e s w i t c h t r i g g e r f u l l y , p r e s s a n d
hold the angle adjustment button for a few seconds until
t h e g r e e n i n d i c a t o r l a m p b l i n k s f a s t .
3. Adjust the cutting depth by pulling the switch
t r i g g e r r e p e a t e d l y s o t h a t t h e o v e r l a p o f t h e t i p s o f t h e
u p p e r a n d l o w e r s h e a r b l a d e s i s 1 t o 3 m m .
Fig.7: (1) U p p e r s h e a r b l a d e (2) L o w e r s h e a r b l a d e
(3) 1 - 3 m m
NOTE: T h e u p p e r b l a d e r e t u r n s t o t h e s h a l l o w e s t
p o s i t i o n w h e n y o u p u l l t h e s w i t c h t r i g g e r a f t e r t h e
u p p e r b l a d e r e a c h e s t h e d e e p e s t p o s i t i o n .
NOTE: If the tool is overloaded while adjusting the
cutting depth adjustment, the green lamp blinks and
red lamp lights up. In this case, turn o the tool, then
remove the cause of the overload, and then adjust the
c u t t i n g d e p t h a g a i n .
4.
Press and hold the angle adjustment button to
complete the adjustment. The green indicator lamp
s t o p s b l i n k i n g , a n d l i g h t s u p .
ASSEMBLY
CAUTION:
Always be sure that the tool is
s itched o and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION:
W hen replacing the shear blades,
always wear gloves so that your hands do not
directly contact the blades.
Removing or installing the shear
blades
1. L o o s e n t h e b o l t s w i t h t h e h e x w r e n c h , t h e n s l i d e
t h e c o v e r s l i g h t l y a n d r e m o v e t h e b o l t s a n d c o v e r , a n d
t h e n t u r n o v e r t h e t o o l .
Fig.8: 1. B o l t 2. C o v e r
2. L o o s e n t h e b o l t w i t h t h e h e x w r e n c h , a n d t h e n
r e m o v e i t .
Fig.9: 1. B o l t
NOTICE:
Do not loosen the nut before loosening
the bolt. O t h e r w i s e , t h e n u t m a y b e d a m a g e d .
3. L o o s e n t h e n u t w i t h t h e b o x w r e n c h , a n d t h e n
r e m o v e i t .
Fig.10: 1. N u t
4. T u r n o v e r t h e t o o l , a n d t h e n r e m o v e t h e b o l t , b l a d e
h o l d e r , u p p e r s h e a r b l a d e , a n d l o w e r s h e a r b l a d e i n
o r d e r .
Fig.11: 1. B o l t 2. B l a d e h o l d e r 3. U p p e r s h e a r b l a d e
4. L o w e r s h e a r b l a d e
5.
A t t a c h t h e l o w e r s h e a r b l a d e , u p p e r s h e a r b l a d e ,
b l a d e h o l d e r , a n d b o l t t o t h e t o o l i n o r d e r .
Fig.12: 1. B o l t 2. B l a d e h o l d e r 3. U p p e r s h e a r b l a d e
4. L o w e r s h e a r b l a d e
NOTICE:
W hen attaching the upper shear blade,
make sure that the upper shear blade is placed in
the direction sho n in the figure.
6. T u r n o v e r t h e t o o l , a n d t h e n a t t a c h t h e n u t t o t h e
t o o l a n d t i g h t e n i t m a n u a l l y .
Fig.13: 1. N u t
NOTICE:
The recommended tightening torque is
approximately 0.5 N • m.
7.
A t t a c h t h e b o l t t o t h e t o o l a n d t i g h t e n i t w i t h t h e
h e x w r e n c h .
Fig.14: 1. B o l t
8. T u r n o v e r t h e t o o l , t h e n a t t a c h t h e c o v e r t o t h e
t o o l , a n d t h e n t i g h t e n t h e b o l t s w i t h t h e h e x w r e n c h .
Fig.15: 1. B o l t 2. C o v e r
NOTICE:
Tighten the bolts with the hex wrench
in the upright position as sho n in the figure.
T i g h t e n i n g t h e b o l t s t o o m u c h m a y d a m a g e t h e b o l t s .
Fig.16: 1. H e x w r e n c h
A f t e r i n s t a l l i n g t h e s h e a r b l a d e s , c h e c k t h e c l e a r a n c e
of shear blades by confirming the following points. If
the clearance is not proper, adjust it by referring to the
section for adjustment for shear blades clearance.
• C h e c k t h a t t h e r e i s n o g a p b e t w e e n t h e u p p e r
s h e a r b l a d e a n d l o w e r s h e a r b l a d e .
Fig.17
• C h e c k t h a t t h e u p p e r s h e a r b l a d e m o v e s a p p r o x i -
m a t e l y 3 m m
Fig.18: 1. U p p e r s h e a r b l a d e
A f t e r i n s t a l l i n g t h e s h e a r b l a d e s , a p p l y o i l t o t h e s h e a r
b l a d e s b y r e f e r r i n g t o t h e s e c t i o n f o r s h e a r b l a d e
m a i n t e n a n c e .
After installing the shear blades, adjust the cutting
d e p t h b y r e f e r r i n g t o t h e s e c t i o n f o r c u t t i n g d e p t h
adjustment.
12 ENGLISH
t o w a r d t h e l o w e r s h e a r b l a d e .