Additional Safety Instructions - Scheppach HC550TC-400V Original Bedienungsanleitung

Vorschau ausblenden Andere Handbücher für HC550TC-400V:

Inhaltsverzeichnis

Verfügbare Sprachen

8 Wear proper clothing

– Do not wear loose clothing or jewellery, as they

can get caught in moving parts.

– When working outdoors, wear slip-resistant

shoes.

– Wear a hairnet over long hair.

9 Use protective gear

– Wear safety glasses.

– Wear a breathing mask during work that cre-

ates dust.

10 Connect the dust extraction equipment

– If there are connections to dust extraction and

collection equipment, make sure that they are

connected and properly used.

11 Do not use the cable for purposes for which it was

not intended

– Never use the cable to pull the plug from the

socket. Protect the cable from heat, oil and

sharp edges.

12 Secure the work piece

– Use clamps or a vice to hold the work piece

firmly. They will hold it more securely than your

hand can.

13 Avoid abnormal postures

– Make sure to stand securely and always keep

your balance.

14 Maintain your tools with care

– For better and safer work, keep cutting tools

sharp and clean.

– Follow the instructions for lubrication and

changing tools.

– Regularly inspect the electric tool's connection

cable, and if it is damaged, have it replaced by

an authorized expert.

– Regularly check extension cords, and replace

them if they are damaged.

– Keep the handles dry, clean and free of oil and

grease.

15 Pull the plug from the socket

– When not using the electric tool, before main-

tenance or when changing tools, such as saw

blades, drills and cutting bits.

16 Do not leave any tool keys inserted

– Before switching on, check to see that keys and

adjustment tools have been removed.

17 Avoid unintentional activation

– When plugging the tool in, make sure that the

switch is turned off.

18 Use outdoor extension cords

– When outdoors, use only extension cords that

are approved and appropriately marked.

– Only use cable reels in the unrolled state.

19 Be alert

– Pay attention to what you do. Approach your

work sensibly. Do not use the electric tool when

you are distracted.

22 | GB

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

20 Check the electric tool for damage

– Before using the electric tool, you must inspect

safety equipment or slightly damaged parts

carefully to ensure that they work properly and

as intended.

– Check to see that the moving parts operate

freely and don't stick, and to make sure no parts

are damaged. All parts must be mounted prop-

erly and meet all the conditions for ensuring

trouble-free operation of the electric tool.

– Damaged safety equipment and parts must be

properly repaired or replaced by a professional

facility, unless otherwise indicated in the user

manual.

– Damaged switches must be replaced by a cus-

tomer service facility.

– Never use an electric tool whose switch cannot

be turned on and off.

21 CAUTION!

– Using other insertion tools and accessories

may cause injury.

22 Have your tool repaired by an electrical expert

– This electric tool meets applicable safety re-

quirements. Repairs must be made only by an

electrical expert using original replacement

parts. Otherwise accidents many occur.

23 Noise

– Wear ear muffs when you use the compressor.

24 Replacing the power cable

– To prevent hazards, leave the replacement of

damaged power cables strictly to the manufac-

turer or a qualified electrician. There is a risk

of electric shock!

25 Inflating tires

– Directly after inflating tires, check the pressure

with a suitable pressure gauge, for example at

your filling station.

26 Roadworthy compressors for building site oper-

ations

– Make sure that all lines and fittings are suitable

for the maximum permissible operating pres-

sure of the compressor.

27 Place of installation

– Set up the compressor on an even surface.

28 Supply hoses at pressures above 7 bar should be

equipped with a safety cable (e.g. a wire rope).