Introduction; Device Description; Scope Of Delivery - Scheppach HS110 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

2. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
we hope your new tool brings you much enjoyment and suc-
cess.
Note:
According to the applicable product liability laws, the manu-
facturer of the device does not assume liability for damages
to the product or damages caused by the product that occurs
due to:
• Improper handling
• Non-compliance of the operating instructions
• Repairs by third parties, not by authorized service techni-
cians
• Installation and replacement of non-original spare parts
• Application other than specified
• A breakdown of the electrical system that occurs due to the
non-compliance of the electric regulations and VDE regula-
tions 0100, DIN 57113 / VDE0113.
We recommend:
Read through the complete text in the operating instructions be-
fore installing and commissioning the device.
The operating instructions are intended to help the user to be-
come familiar with the machine and take advantage of its ap-
plication possibilities in accordance with the recommendations.
The operating instructions contain important information on
how to operate the machine safely, professionally and econom-
ically, how to avoid danger, costly repairs, reduce downtimes
and how to increase reliability and service life of the machine.
In addition to the safety regulations in the operating instruc-
tions, you have to meet the applicable regulations that apply
for the operation of the machine in your country.
Keep the operating instructions package with the machine at
all times and store it in a plastic cover to protect it from dirt
and moisture. Read the instruction manual each time before
operating the machine and carefully follow its information. The
machine can only be operated by persons who were instructed
concerning the operation of the machine and who are informed
about the associated dangers. The minimum age requirement
must be complied with.
In addition to the safety notes contained in the present oper-
ating instructions and the special regulations of your country,
the generally recognized technical rules for the operation of
woodworking machines must be observed.
We accept no liability for damage or accidents which arise
due to non-observance of these instructions and the safety in-
formation.

3. Device description

1. Saw table
2. Saw blade guard
3. Riving knife (not visible)
4. Saw blade (not visible)
5. Table insert
6. Table width extender
7. Locking handle
8. Scale
9. Handwheel
10. Crank handle
11. Base frame
12. On/off switch
13. Cam lever
14. Parallel stop
15. Guide rail
16. Suction adapter
17. Push stick
18. Bracket for saw blade storage
19. Legs (4x)
20. Central struts (4x)
21. Rubber feet (4x)
22. Stand brackets (2x)
23. Attachment points
24. Table brackets,
25. Countersunk screws of the table insert
26. Fixing screws of the riving knife
27. Knurled nut with screw
28. Groove
29. Knurled screw
30. Stop rail
31. Transverse stop

4. Scope of delivery

• Table saw with pre-mounted 24 tooth saw blade
• Saw blade guard
• Riving knife
• Parallel stop
• Stop rail
• Transverse stop
• Table width extension (2x)
• Push stick
• Pillars (4x)
• Centre struts (4x)
• Rubber feet (4x)
• Stand bracket (2x)
• Table supports (4x)
• Translation of Original Operating Manual
a. Hexagon head screw with collar, 8 units;
b. Carriage bolt, 12 units;
c. U-washer, 18 units;
d. Spring washer, 12 units;
e. Nuts, 18 units
f. Hexagon head screw with cross slot with mounted
U-washer/spring washer, 12 units;
g. Open-end spanner, size 8/10
h. Ring spanner, size 10/22
i. Allen key HX 6
GB/IE/NI 31