Teac CD-P750 DAB Bedienungsanleitung Seite 10

2 – Names and Functions of Parts (continued)
PHONES jack/knob
Use this standard stereo jack to connect stereo headphones.
Use an adapter to connect headphones with a mini plug.
Use the PHONES knob to adjust the headphone output level.
PHONES jack output can be lowered up to −18 dB in 1dB inter-
vals using the A.Out Att. setting screen. (see "Adjusting the
analog output" on page 38)
CAUTION
Before connecting headphones, minimize the volume with the
PHONES knob. Failure to do so could result in a sudden loud
noise that could harm hearing, for example.
AUX IN jack
This stereo mini jack is an audio line input jack.
Connect a portable digital player or other external audio device
here. (see "Using the AUX IN jack" on page 38)
CAUTION
i Before connecting another device to the AUX IN jack, minimize
the volume of that device. Failure to do so could result in a sud-
den loud noise that could harm hearing, for example.
i Before connecting or disconnecting with the AUX IN jack,
set the current source to something other than AUX (CD or
Bluetooth) or turn the unit off.
Remote control signal receiver
Signals from the wireless remote control (RC-1336) are received
here. When operating the remote control, point it toward this
receiver.
1 [PROGRAM] button
i Press to input track number 1 when the current source is CD,
USB or SD and the playback area is set to "All". (see "Selecting
tracks directly" on page 22)
i When the current source is DAB or FM, press to tune in a pre-
set station.
i When the current source is CD and shift mode is active
(SHIFT indicator lit), press this to start program setting mode.
Press this to check and edit the program after it has been pre-
pared. (see "Preparing the program" on page 26)
NOTE
i The number buttons on the unit (1 [PROGRAM] – 0 [DUB])
can be used to specify numbers for track selection. For track
numbers, a maximum of two digits can be input for audio CDs
and three digits for data CDs. (see "Selecting tracks directly" on
page 22)
i When in shift mode (SHIFT indicator lit), pressing a number
button will change the setting of the function shown in white
lettering below the button.
2 [P.O.PLAY] button
i Press to input track number 2 when the current source is CD,
USB or SD and the playback area is set to "All". (see "Selecting
tracks directly" on page 22)
i When the current source is DAB or FM, press to tune in a pre-
set station.
i When in shift mode (SHIFT indicator lit), press to turn the
power-on-play function on/off. (see "Using the power-on-play
function" on page 28)
10
3 [RANDOM] button
i Press to input track number 3 when the current source is CD,
USB or SD and the playback area is set to "All". (see "Selecting
tracks directly" on page 22)
i When the current source is DAB or FM, press to tune in a pre-
set station.
i When the current source is CD, USB or SD, and shift mode is
active (SHIFT indicator lit), press to switch between ordi-
nary and random playback modes. (see "Playback modes" on
page 24)
4 [REPEAT] button
i Press to input track number 4 when the current source is CD,
USB or SD and the playback area is set to "All". (see "Selecting
tracks directly" on page 22)
i When the current source is DAB or FM, press to tune in a pre-
set station.
i When the current source is CD, USB or SD, and shift mode
is active (SHIFT indicator lit), press to cycle through repeat
playback modes (ordinary playback, single repeat and all
repeat playback modes). (see "Ordinary repeat playback set-
tings" on page 25)
5 [A-B REP] button
i Press to input track number 5 when the current source is CD,
USB or SD and the playback area is set to "All". (see "Selecting
tracks directly" on page 22)
i When the current source is DAB or FM, press to tune in a pre-
set station.
i When the current source is CD and shift mode is active
(SHIFT indicator lit), press to set the A-B repeat function
starting (A) and ending (B) points. (see "A-B repeat playback
settings (audio CDs only)" on page 25)
6 [A. PRESET] button
i Press to input track number 6 when the current source is CD,
USB or SD and the playback area is set to "All". (see "Selecting
tracks directly" on page 22)
i When the current source is DAB or FM, press to tune in a pre-
set station.
i When the current source is DAB or FM and shift mode is active
(SHIFT indicator lit), press to automatically program the pre-
set stations. (see "Setting radio station presets automatically"
on page 33)
7 [M.PRESET] button
i Press to input track number 7 when the current source is CD,
USB or SD and the playback area is set to "All". (see "Selecting
tracks directly" on page 22)
i When the current source is DAB or FM, press to tune in a pre-
set station.
i When the current source is DAB or FM and shift mode is active
(SHIFT indicator lit), press to manually program the preset
stations. (see "Setting radio station presets manually" on
page 33)