Beninca SAM-Serie Bedienungsanleitung Seite 33

MENU
Selecting this function, the receiver sets in standby (Push) of a transmitter code to assign to the step-step function. Press
PP
the transmitter key you intend to assign to this function.
If the code is valid, it is saved and the message OK is displayed
Selecting this function, the receiver sets in standby (Push) of a transmitter code to assign to the second radio channel.
2Ch
Press the transmitter key you intend to assign to this function.
If the code is valid, it is saved and the message OK is displayed
Selecting this function, the receiver sets in standby (push) of a transmitter code to assign to the pedestrian opening
ped
function (see TPED parameter). Press the transmitter key you intend to assign to this function.
If the code is valid, it is saved and the message OK is displayed
Selecting this function, the receiver sets in standby (Push) of a transmitter code to assign to the STOP function. Press
STOP
the transmitter key you intend to assign to this function.
If the code is valid, it is saved and the message OK is displayed
n tx
Selecting this function, the LCD display shows the number of transmitters currently saved in the receiver.
Selecting this function, the receiver sets in standby (Push) of a transmitter code to delete from the memory.
CLR
If the code is valid, it is cancelled and the message OK is displayed
Completely deletes the receiver memory. Confirmation is required of the operation.
RTR
By selecting this function, the receiver sets in standby (Push) of a new PGM press to confirm the operation.
At the end of the deletion, the message OK is displayed.
It displays the number of complete cycles (open+close) carried out by automation. The first press of the <PG> button displays the first
4 digits, the second press displays the last 4. e.g. <PG> 0012 >>> <PG> 3456: executed 123.456 cycles.
This function allows you to enable the maintenance signal request after a number of manoeuvres established by the installation tech-
nician. To enable and select the number of manoeuvres, proceed as follows:
Press the <PG> button. The display shows OFF, which indicates the function is disabled (default value).
With the <+> and <-> buttons, select one of the numerical values proposed (from OFF to 100). The values should be intended as
hundreds of manoeuvre cycles (e.g.: the value 50 indicates 5000 manoeuvres). Press the OK button to enable the function. The dis-
play shows the message PROG. The maintenance request is signalled to the user while maintaining the flashing indicator light on for
another 10 s after conclusion of the opening or closure manoeuvre.
Control panel RESET ATTENTION!: It returns the control panel to the default values.
Pressing the <PG> button for the first time causes the RES message to flash; pressing the <PG> button again resets the control panel.
Note: The transmitters are not deleted from the receiver or the access password.
All the logic and all the parameters are brought to the default values and it is therefore necessary to repeat the autoset procedure.
This function is used to set the optimal automation operating values and, at the end of the procedure, the parameters of DISPLACE-
MENT, WORKING TIME and SLOWDOWN are adjusted.
To autoset, proceed as follows:
Ensure that there are no obstacles in the operating area of the gates, if necessary, cordon off the area to prevent access to people,
animals, cars, etc.
During the autoset phase, the anti-crushing function is not active.
b) Select the AUTO function and press OK.
c) Select with the button <+> or <-> the sub-menu nLSu, LSU or ENC according to the presence of the limit switch and/or encoder:
nLSu: if the motor is without a limit switch and encoder
LSU: if the motor is equipped with a limit switch and encoder
ENC: if the motor is equipped with an encoder and without a limit switch.
d) having selected the item, press OK to start the autoset phase.
The central panel executes a series of manoeuvres for learning of the gate stroke and for configuration of the parameters.
Initially both the gates are brought to the opening position, then after a few opening and closure manoeuvres at different speeds, of
one or both gates, the control panel displays the message OK. If the operation does not have a positive outcome, the ERR message
is displayed. Repeat the operation after checking the wiring and the presence of obstacles
During the manoeuvres, the display shows each code: OPEN during opening of motor 1 or 2 and CLOS during closure of motor 1 or 2.
RADIO (RAD)
NUMBER OF MANOUEVRES (Nman)
MAINTENANCE CYCLES (maci)
RESET (RES)
AUTOSET (AUTO)
FUNZIONE
EN
33