Environmental Considerations - Teka AFF-Serie Bedienungsanleitung

without aff ecting the product's essen-
tial features.
Environmental
considerations
The symbol on the product
or its packaging means that this
product cannot be treated like
ordinary household waste. This
product must be taken to a recycling
collection point for electrical and
electronic appliances. By ensuring
that this product is disposed of
correctly, you will avoid harming the
environment and public health, which
could happen if this product is not
handled properly. For more detailed
information about recycling this
product, please contact your local
authority, household waste service
or the store where you pur-chased
the product. The packaging materials
used are environmentally friendly
and can be recycled completely.
Plastic compo-nents are marked
>PE<, >LD<, EPS<, etc. Dispose of
packaging materials, like household
waste, in your local container.
F u l f i l l m e n t w i t h
Efficiency of the appliance:
-Appliance has been tested according
to standard EN 60350-2 and the
obtained value, in Wh/kg, is available
in the appliance's rating plate.
Following advices will help you to
save energy anytime you cook:
* Use the correct lid for each pot
whenever is possible. Cooking
without lid uses more energy.
* Use pans with flat bases and
appropriate base diameters in order
to match size of the cooking zone.
Pan manufacturers usually provide
top diameter of the pot that is always
larger than base diameter.
* When water is used for cooking, use
little quantities in order to preserve
vitamins and minerals of vegetables
and set the minimum power level
that allows maintaining the cooking.
High power level is unnecessary and
a waste of energy.
* Use small pots with small quantities
of food.
If something does not work
Before calling the technical service,
perform the verifications described
below.
The appliance does not work:
Ensure that the power cable is
plugged in.
The induction zones do not produce
heat:
The container is not appropriate (it does
not have a ferromagnetic bottom or is
too small). Check that the bottom of the
container attracts a magnet, or use a
larger container.
A humming is heard when starting to
cook in the induction zones:
With containers which are not very thick
or not of one piece, the humming results
from the transmission of energy directly
to the bottom of the container. The
humming is not a defect, but if you wish
to avoid it anyway, reduce the power
E n e r g y
level slightly or use a container with a
thicker bottom, and/or of one piece.
The touch control does not light up or,
despite lighting, does not respond:
No heating zone has been selected. Be
sure to select a heating zone befo-re
operating it.
There is humidity on the sensors,
and/or your fingers are wet. Keep
the touch control surface and/
or your fingers clean and dry.
The locking function is activated. Unlock
the controls.
The sound of a fan is heard
while cooking, which continues
even after cooking has ended:
The induction zones have a fan to keep
the electronics cool. This only operates
when the electronic circuits get hot.
It stops again when the circuits cool
whether the hob is turned on or not.
The symbol will appear
power indicator of a hotplate:
The induction system does not fi nd a
pot or pan on a hotplate or it is of an
unsuited type.
The hotplate will switch off and the
message C81 or C82 will appear on
the indicators:
Excessive temperature in the electro-
nics or on the glass. Wait for a while for
the electronics to cool down or remove
the pot or pan so that the glass can cool.
C85 appears on the indicator of one
of the hotplates:
The pot or pan used is of an unsuited
type. Switch off the hob, switch it on
again and try with another pot or pan.
The appliance switches off and the
message C90 appears on the power
indicators (3):
The touch control detects on/off (1)
sensor is covered and doesn't allow
switching on the cooktop. Remove the
possible objects or liquids keeping the
touch control surface, clean and dry until
the message disappears.
The appliance switches off and the
message C91 appears on the power
indicators (3):
The touch control detects Stop&Go
sensor (6) is covered and doesn't allow
to handle the cooktop. Remove the
possible objects or liquids keeping the
touch control surface, clean and dry,
then press twice Stop&Go (6) sensor
for removing the message and return to
normal operation.
EN
on the
47