Environmental Considerations - Teka IZC 63632 MST Montageanleitung Und Empfehlungen Zur Verendung Und Wartung

EN
that have melted onto the surface
must be removed immediately using
a scraper.
Metallic sheens are caused by dragging
metal pots and pans over the glass.
These can be removed by cleaning
thoroughly using a special cleaner
for ceramic glass hot plates, although
you may need to repeat the cleaning
process several times.
Warning:
A pot or pan may become stuck
to the glass due to a product having
melted between them. Do not try to
lift the pot while the heating zone is
cold! This could break the glass.
Do not step on the glass or lean
on it as it could break and cau-se
injury. Do not use the glass as a
surface for placing objects.
TEKA INDUSTRIAL S.A. reserves the
right to make changes to its manuals
that it deems necessary or useful,
tial features.
Environmental
considerations
The symbol on the product
or its packaging means that this
product cannot be treated like
ordinary household waste. This
product must be taken to a recycling
collection point for electrical and
electronic appliances. By ensuring
that this product is disposed of
correctly, you will avoid harming
the environment and public health,
which could happen if this product
is not handled properly. For more
detailed information about recycling
this product, please contact your
local authority, household waste
service or the store where you pur-
chased the product.
The packaging materials used are
environmentally friendly and can be
recycled completely. Plastic compo-
nents are marked >PE<, >LD<, EPS<,
etc. Dispose of packaging materials,
like household waste, in your local
38
container.
F u l f i l l m e n t w i t h
Efficiency of the appliance:
-Appliance has been tested
according to standard EN 60350-2
and the obtained value, in Wh/Kg,
is available in the appliance's rating
plate.
Following advices will help you to
save energy anytime you cook:
* Use the correct lid for each pot
whenever is possible. Cooking
without lid uses more energy.
* Use pans with flat bases and
appropriate base diameters in order
to match size of the cooking zone.
Pan manufacturers usually provide
top diameter of the pot that is always
larger than base diameter.
* When water is used for cooking, use
little quantities in order to preserve
vitamins and minerals of vegetables
and set the minimum power level
that allows maintaining the cooking.
High power level is unnecessary and
a waste of energy.
* Use small pots with small quantities
of food.
If something does not work
Before calling the technical service,
perform the verifications described
below.
The appliance does not work:
Ensure that the power cable is plugged
in.
The induction zones do not produce
heat:
The container is not appropriate (it does
not have a ferromagnetic bottom or is
too small). Check that the bottom of the
container attracts a magnet, or use a
larger container.
A humming is heard when starting to
cook in the induction zones:
With containers which are not very thick
or not of one piece, the humming results
from the transmission of energy directly
to the bottom of the container. The
humming is not a defect, but if you wish
to avoid it anyway, reduce the power
level slightly or use a container with
a thicker bottom, and/or of one piece.
The touch control does not light up or,
despite lighting, does not respond:
E n e r g y No heating zone has been selected. Be
sure to select a heating zone befo-re
operating it.
There is humidity on the sensors,
and/or your fingers are wet. Keep
the touch control surface and/
or your fingers clean and dry.
The locking function is activated. Unlock
the controls.
The sound of a fan is heard
while cooking, which continues
even after cooking has ended:
The induction zones have a fan to keep
the electronics cool. This only operates
when the electronic circuits get hot.
It stops again when the circuits cool
whether the hob is turned on or not.
The symbol will appear
power indicator of a hotplate:
pot or pan on a hotplate or it is of an
unsuited type.
message C81 or C82 will appear on
the indicators:
Excessive temperature in the electro-
nics or on the glass. Wait for a while for
the electronics to cool down or remove
the pot or pan so that the glass can cool.
C85 appears on the indicator of one
of the hotplates:
The pot or pan used is of an unsuited
again and try with another pot or pan.
message C90 appears on the power
indicators (3):
sensor is covered and doesn't allow
switching on the cooktop. Remove the
possible objects or liquids keeping the
touch control surface, clean and dry until
the message disappears.
message C91 appears on the power
indicators (3):
The touch control detects Stop&Go
sensor (6) is covered and doesn't allow
to handle the cooktop. Remove the
possible objects or liquids keeping the
touch control surface, clean and dry,
then press twice Stop&Go (6) sensor
for removing the message and return
to normal operation.
on the