Cleaning And Maintenance; Environmental Considerations - Teka TZC 32320 BK TTC Montageanleitung Und Empfehlungen Zur Verendung Und Wartung

EN
products containing sugar on the
glass while the surface is hot as
these could damage it.

Cleaning and maintenance

To keep the appliance in good
condition, clean it using suitable
products and implements once it has
cooled down. This will make the job
easier and avoid the build-up of dirt
Never use harsh cleaning products or
tools that could scratch the surface, or
steam-operated equipment.
Light dirt not stuck to the surface can
be cleaned using a damp cloth and a
gentle detergent or warm soapy water.
However, for deeper stains or grease
use a special cleaner for ceramic hot
plates and follow the instructions on
the bottle. Dirt that is firmly stuck due
to being burned repeatedly can be
removed using a scraper with a blade.
Slight tinges of colour are caused by
pots and pans with dry grease residue
underneath or due to grease between
the glass and the pot during cooking.
These can be removed using a nickel
scourer with water or a special cleaner
for ceramic hot plates. Plastic objects,
sugar or food containing a lot of sugar
that have melted onto the surface
must be removed immediately using
a scraper.
Metallic sheens are caused by
dragging metal pots and pans over
the glass. They can be removed by
cleaning thoroughly using a special
cleaner for ceramic glass hot plates,
although you may need to repeat the
cleaning process several times.
Warning:
Use the glass scraper carefully. The
blade could cause injury!
If you use the scraper
incorrectly, the blade could break
and a fragment could get caught
between the surrounding trim and
the glass. If this happens, do not try
to remove it using your hands,
carefully use tweezers or a knife
with a fine edge. (See fig. 3)
38
Only use the blade on the
ceramic surface, avoiding the
scraper casing coming into contact
with the glass because this could
scratch it.
U s e b l a d e s i n p e r f e c t
condition. Immediately replace the
blade if it is damaged in any way.
After you have finished with
the scraper, withdraw the blade and
lock it. (See fig. 4)
fig. 4
Using the scraper
Blade protected Blade unprotected
A pot or pan may become
stuck to the glass due to a product
having melted between them. Do
not try to lift the pot while the hot
plate is cold! This could cause the
glass break.
Do not step on the glass or
lean on it as it could break and
cause injury. Do not use the glass
as a surface for putting objects.
TEKA INDUSTRIAL S.A. reserves
the right to make changes to its
manuals that it deems necessary or
useful, without affecting the product's
essential features.
Environmental
considerations
The symbol on the product
or its packaging means that this
product cannot be treated like
ordinary household waste.This
product must be taken to a recycling
collection point for electrical and
electronic appliances. By ensuring
fig. 3
that this product is disposed of
correctly, you will avoid harming
the environment and public health,
which could happen if this product
is not handled properly. For more
detailed information about recycling
this product, please contact your
local authority, household waste
service or the store where you
purchased the product.
The packaging materials used are
environmentally-friendly and can
be recycled completely. Plastic
components are marked >PE<, LD<,
>EPS<, etc. Dispose packaging
materials, like household waste, in
your local container.
If something does not work
Before calling the technical service,
perform the verifications specified
below.
The appliance does not work:
Ensure that the power cable is plugged
in.
The pot sticks to the glass:
If there is molten material between
the pot and the glass, set the hot
plate to maximum power and try to
separate them.
Single Sensor Error :
If any of the sensors is active more
than 10 seconds, this error situation
occurs and error code"F1" is showed.
This error can be related with different
roots. One of them is that there may
be an object (fork, knife...) on the any
of the sensor.
Make sure that there is no any object
on the control unit, hob glass is wiped
with a dry cloth. If error situation
continue after this solution, please
take out plug or switch off fuse switch
for 10 second.
Plural Sensor Error:
If more than 2 sensors are sensed at
same time, this error situation occurs
and error code"F2" is displayed.
Potential root reasons of the
problem :