Inhaltsverzeichnis
Werbung
GB
Raise the lower guard with the retracting handle and make sure it moves freely and
does not touch the blade or any other part, in all angles and depths of cut.
D
b) Check the operation of the lower guard spring. If the guard and the spring are not
operating properly, they must be serviced before use. Lower guard may operate
sluggishly due to damaged parts, gummy deposits, or a build-up of debris.
c)
Lower guard should be retracted manually only for special cuts such as "plunge cuts"
NL
and "compound cuts." Raise lower guard by retracting handle and as soon as blade
enters the material, the lower guard must be released. For all other sawing, the lower
guard should operate automatically.
F
d) Always observe that the lower guard is covering the blade before placing saw down
on bench or floor. An unprotected, coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be aware of the time it takes for the blade
E
to stop after switch is released.
Before using the circular saw
P
•
Check the following points:
•
does the voltage of the motor correspond with the mains voltage (appliances for a
mains voltage of 230 V
I
•
are the mains lead and the mains plug in a good condition: solid, without any
loose ends or damage;
•
is the saw blade missing any teeth or showing
S
any cracks, it so must be replaced immediately.
•
Make sure the blade is secure.
•
Use this circular saw to saw only wood, wood-like products.
SF
•
Do not use circular saw blades wich are deformed or damaged.
•
Do not use HSS blades.
•
Only use blades meeting the required dimensions, as well as data and descriptions;
Never apply any blades of which the thickness is
N
greater than that of the riving knife.
•
Do not stop the blade of a circular saw by pressing the blade from the side.
•
Check that the blade guard can freely move and fully closes.
DK
•
Never lock-up the guard in the open position.
•
Never put sideward pressure on the blade. This may cause the blade to break.
•
Be careful when cutting wood with knots, nails or cracks in it and/or dirt on it, as these
can cause the blade to get stuck.
•
Never leave the circular saw unattended.
•
Use this circular saw to saw only wood or wood-like products.
Using the machine
•
Use clamps or a vice to hold the work.
•
Never remove wood chips and saw dust that is close to the saw blade with your
hands. If there are small pieces of wood left between the fixed and the movable parts,
the circular saw will have to be stopped. The plug needs to be removed from the
socket, before any left piece can be removed.
•
Check that the blade is suitable for the spindle speed of the circular saw. Do not
attempt to cut before the circular saw has reached full speed. Make sure the circular
saw runs without load (i.e. is not in contact with the work) when you switch it on. The
circular saw must have reached its full speed first.
•
Never cut wood that is thicker than the depth of the saw blade.
•
When cutting in wooden walls or floors, check there is no wiring or piping where you
intend to cut.
06
Tilkobling/frakobling
Fig. E.
•
Tryk på knappen (B) med højre hånds tommelfinger og hold knappen trykt ned.
•
Tryk derefter på knappen (A). Rundsaven starter nu.
•
Rundsaven stopper, når du slipper knappen (A).
Ibrugtagning
•
Klem arbejdsemnet fast, således at begge hænderne er fri til at fastholde og betjene
rundsaven.
•
Tilkobl rundsaven og placér savebunden på arbejdsemnet.
•
Tryk forsigtigt på rundsaven og bevæg den langsomt frem langs den på forhånd tegnede
skærelinie.
•
Tryk savebunden fast mod arbejdsemnet.
Lad rundsaven gøre arbejdet! Undlad derfor at udøve for meget tryk på
rundsaven.
5. VEDLIGEHOLDELSE
Sørg for at maskinen ikke står under strøm, når der udføres
vedligeholdelsesarbejder på mekanikken.
Maskinerne er udviklet til at fungere længe uden problemer med et minimum af
vedligeholdelse. Ved at rengøre maskinen regelmæssigt og behandle den korrekt, bidrager
De til en længere levetid for maskinen.
Fejl
Hvis rundsaven ikke virker hensigtsmæssigt, kan du gennemgå følgende mulige årsager og
tilhørende løsninger for at afhjælpe problemerne.
1.
Elektromotoren overophedes.
•
Motoren overbelastes, fordi der saves for store arbejdsemner.
Sav i et lavere tempo og lad motoren køle af.
•
Motoren er defekt.
Få rundsaven repareret eller set efter hos en forhandler.
2.
Maskinen virker ikke, selv om den er tilkoblet.
•
Fejl i netledningen.
Kontrollér netledningen for brud.
•
Afbryderen er defekt.
Få rundsaven repareret eller set efter hos en forhandler.
3.
Det er vanskeligt at føre arbejdsemnet i en ret linie langs savklingen og savskæret er
uregelmæssigt.
•
Savklingen er bøjet eller sløv.
Udskift savklingen.
4.
Rundsaven støjer og/eller går meget uregelmæssigt.
•
Kulbørsterne er slidte.
Få rundsaven repareret eller set efter hos en forhandler.
Ferm
Ferm
UK
D
NL
F
E
P
I
DK
SF
N
DK
95
Werbung
Inhaltsverzeichnis
