Inhaltsverzeichnis
Werbung
SPARE PARTS LIST FKZ-205
REF NR
DESCRIPTION
26
SPRING
67
GEAR WHEEL
32
POSITIONING RING
30
CLAMP RING
88
ROTOR-ASSEMBLEY
84
STATOR ASSEMBLY
82
CARBON BRUSH WITH SPRING
80
BRUSH HOLDER
98
CAPACITOR
97
SWITCH
50
FERM NR
407630
COMPOUND MITRE SAW
407631
407632
THE NUMBERS IN THE FOLLOWING TEXT
407633
CORRESPOND WITH THE PICTURES AT PAGE 2
407634
407635
machine functions and how to operate it. Maintain the
407636
machine in accordance with the instructions to make sure it
407637
functions properly.
407638
TECHNICAL SPECIFICATIONS
407639
Voltage
Frequency
Power input
No load speed
Disc diameter
Max. cutting depth 90°
Max. cutting depth 45°
Weight
Lpa (sound pressure)
Lwa (sound power level)
Vibration value
DESCRIPTION
Fig. 1
1. Grip with switch
2. Unlocking button
3. Motor housing + cover carbon brushes
4. Saw blade attachment
5. Moveable safety guard
6. Table adjustment screws
7. Rotary table
8. Degree scale
9. Fastening holes
10. Bevel adjustment bolt
11. Protective cover
12. Rotary knob for bevelling
PACKAGE CONTENTS
1 Mitre machine
1 Saw blade Ø205 mm
1 Instruction manual
1 Safety instructions
1 Guarantee card
Check the machine, loose parts and accessories for
transport damage.
SAFETY INSTRUCTIONS
The following symbols are used throughout this manual:
Ferm
Ferm
Carefully read this manual before using the
machine. Make sure that you know how the
| 230 V~
| 50 Hz
| 800 W
| 4500/min
| 205 x 18 mm
| 120x50 mm
| 70x55 mm
| 7.0 kg
| 88.9 dB(A)
| 101.9 dB(A)
| 2.5 m/s
2
CE Conforms to the applicable European safety
standards.
Class II equipment – doubly insulated – the plug
does not have to be earthed.
Danger of bodily injury or material damage.
Denotes risk of electric shock.
Read the instructions.
Keep bystanders at a distance.
Immediately unplug the plug from the mains
electricity in the case that the cord gets damaged
and during maintenance.
Wear eye and ear protectors.
Faulty and/or discarded electrical or electronic
apparatus have to be collected at the appropriate
recycling locations.
ELECTRICAL SAFETY
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Keep these instructions in a safe place!
Always check that the power supply corresponds to
the voltage on the rating plate.
The machine is double insulated in accordance
with EN50144; therefore no earth wire is required.
Replacing cables or plugs
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm
2
. When using a cable reel always unwind
the reel completely.
SPECIAL SAFETY INSTRUCTIONS
BEFORE EACH USE
•
Check the Mitre machine. If any part of the Mitre
machine is missing, bent or unusable in another way, or
if electrical faults occur, switch off the machine and
remove the plug from the socket. Replace all missing,
damaged or faulty parts, before using the machine again.
•
Make sure that hands, eyes, face and ears are well
protected.
•
Use of safety goggles without the CE quality mark can
lead to serious injury if the glass breaks.
3
Werbung
Inhaltsverzeichnis
