Inhaltsverzeichnis
Werbung
•
Redskabet virker ikke.
•
Strømtilførslen er blevet
afbrudt.
•
•
Savklingen er skæv eller
•
døv.
•
Savklingen er over
•
ophedet eller skæv.
•
Kullene er slidte.
•
Rengøring
Rengør regelmæssigt maskinkappen med en blød klud, helst efter hvert brug. Sørg for at
ventilationshullerne er fri for støv og snavs. Brug en blød klud, der er vædet i sæbevand til at
fjerne hårdnakket snavs. Brug ingen opløsningsmidler, så som benzin, alkohol, ammoniak,
osv. Den slags stoffer beskadiger kunststofdelene.
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en enhed, kontakt venligst serviceadressen på
DK
garantibeviset. På bagsiden af denne manual finder du en tegning med alle dele, der kan
bestilles.
Miljø
For at undgå transportbeskadigelse leveres maskinen i en solid emballage. Emballagen er så
vidt muligt lavet af genbrugsmateriale. Genbrug derfor emballagen.
Defekte og/eller kasserede elektriske eller elektroniske maskiner skal afleveres på
en genbrugsplads.
Garanti
Se venligst garantibetingelserne på garantikortet, som er vedlagt separat.
102
Kontroller om der er
•
Afbryderen er
defekter i forbindelsen til
beskadiget.
strømforsyningen.
Lever redskabet ind til
•
Kontakt venligst
Deres forhandler til
serviceadressen på
eftersyn eller reparation.
garantibeviset.
Udskift savklingen.
•
Arbejdsemnet begynder
at vibrere kraftigt under
savningen.
Udskift savklingen.
•
Redskaber kører
larmende og/eller meget
ujævnt.
Lever redskabet ind hos.
•
Kontakt venligst
serviceadressen på
garantibeviset.
Accuracy.
Faulty and/or discarded electrical or electronic apparatus have to be collected at
the appropriate recycling locations.
Special safety instructions
Before using the appliance:
•
Check the following points:
•
Does the voltage of the motor (230 V) correspond with the mains voltage?
•
Are the feeder cable and plug in good condition: sturdy, without loose bits or
damage?
•
Has the saw blade lost any teeth and is it showing cracks or fractures?
•
If so, replace the saw blade immediately.
•
Is there enough room under the workpiece so that the saw blade does not come into
contact with the floor or work table as it moves up and down?
•
Do the teeth of the saw blade point upwards?
•
Always wear protective goggles when using the appliance.
•
Maintain the appliance carefully.
•
Do not use the appliance in a wet environment.
•
Do not use the appliance for material which contains asbestos.
•
Never leave the jigsaw unattended.
Check that the switch is not interlocked in the 'On' position
Using the appliance
•
Clamp the workpiece that you will be sawing in firmly into place.
•
Remove any wood residue that is near or stuck to the surface of the saw blade; do not use
your hand for this. Switch the appliance off before removing any residue!
•
Always switch the jigsaw on in idle, i.e. switch the jigsaw on before bringing it into contact
with the workpiece.
•
When sawing the wood watch out for knots, nails, cracks and/or dirt deposits.
These can cause the saw blade to jam dangerously. Also watch out for this with waste
wood. This often requires less careful sawing, so there is a danger that you may not be
quite so careful about watching out for irregularities in the wood.
•
Do not saw workpieces that are thicker than the length of the saw blade.
•
Do not touch metal parts of the jigsaw when sawing in walls or floors in which there could
be electricity cables. Hold the jigsaw tightly with both hands on the plastic grip so that you
do not touch parts that could become live if you accidentally saw through an electricity
cable.
•
When you have finished sawing, switch off the appliance first and wait until the saw blade
comes to a standstill before removing it from the workpiece.
•
Do not use long extension cables.
•
Keep the plastic guard in place while the jigsaw is in use.
Ferm
Ferm
UK
07
Werbung
Inhaltsverzeichnis
