Buckle The Child; Change Position Of The Harness; Adjust The Back Rest; Adjust The Hood - Emmaljunga KITE 150 Bedienungsanleitung

4) Buckle the child

1. Place the 5 harness straps in front of the
child so that the child is not sitting on
them.
2. Assemble the left shoulder and waist
straps by sliding the upper left buckle
into the lower left buckle until it clicks into
position.
3. Assemble the right shoulder and waist
straps by sliding the upper right buckle
into the lower right buckle until it clicks
into position.
4. Click the right buckle over the left buckle
until they are held together as a unit. It
is very important that they sit together
properly and that they cannot be pulled
apart.
5. Lock the harness with the harness lock on
the crotch strap with a "CLICK". Adjust the
harness using the sliding adjusters on the
shoulder and hip belts so that the belt fits
snugly on the child's body.
6. Press the buttons to unlock the harness.

5) Change position of the harness

Shoulder straps
1. Open the backrest pocket (Attached with
velcro strip)
2. Pull the shoulder strap attachment
backwards through the backrest plate.
3. Twist the attachment and pull it forward
through the holes (backrest and fabric).
4. Insert the strap through the other opening
and refasten the harness.
5. Close the backrest pocket.
Crotch strap
6. Unfasten the crotch strap attachment
from the rest of the harness and guide the
crotch strap down through the seat plate.
7. Insert the strap through the other opening
and refasten the harness.
30
WARNING
-
Always check that the belt is properly
closed by pulling on it.
-
Always fasten the child in with the
harness when the child is sitting in
the stroller. Check that all buckles
are correctly fastened and that the
harness is securely assembled in the
stroller.
WARNING
-
Before you use the pram again
always check that the seat unit fabric
is secure and that all press studs are
securely and properly fastened.
-
It is important that the seat unit
fabric is always correctly attached.
-
Never use the pram without making
sure the seat unit fabric is correctly
assembled on the frame first.
V.1.1

6) Adjust the back rest

Lower the backrest (lying position)
Brake the stroller
1. Open the click buckle behind the backrest.
(NOTE! The strap at the top of the handle
must NOT be opened).
2. Hold one hand as a support behind the
backrest and then open the zippers in the
seat all the way down. Lower the backrest
carefully to the reclining position.
3. Pull the snap buckle with the short straps
around the handlebar, one on each side,
and fasten these with the snap buckle
with the long straps behind the backrest.
Important! Check that the buckles with the
short straps are pulled outside / around the
handlebars (not inside)
Raise the backrest (seat position 1)
Brake the stroller
4. Hold one hand as a support behind the
backrest. Gently push up on the backrest.
Fold in the inner fabric with the other hand behind the seat and then close both
zippers in the seat all the way up.
Raise the backrest (seat position 2)
5. Open the click buckle behind the back. (NOTE! The strap at the top of the handle
must NOT be opened) To raise the sitting position from position 1 to position 2, pull
the long straps with the click buckle around the handlebars and click them into each
other behind the back. WARNING Never place the backrest in any other position
than the above mentioned.

7) Adjust the hood

1. Pull the hood gently forward or backward to the desired position.

8) Car seat adapter (Accessory)

Unfold/Fold the adapater
1. Unfold the adapter folding up the two (left
and right) upper parts upwards until they
"CLICK" into locked upright position.
2. To fold the adpater, first move the unlock
button indicated by point 1 upwards.
Then rotate the plastic part down towards
the seat. Left and right side. This step can also be performed when the adpater is
attached to the stroller.
V.1.1
WARNING
-
Make sure that the stroller is parked
on a level surface and that the child
is correctly harnessed.
-
Never leave the child unattended.
WARNING
TIPPING RISK
Never release the handlebar when
the backrest is folded down.
The
buggy is tested according to the standard
EN1888 for tipping risk. Given the small
weight of the buggy and the long backrest,
there is a potential risk of tipping when the
backrest is in a lying position if the child
is not correctly and tightly fastened in the
5-point harness. Therefore, it is important
that you follow the instructions not to
release the handlebars after lowering the
backrest.
WARNING
-
Before you use the stroller, always
make sure the adpater is correctly
assembled on the seat plate.
-
Always read the instructions of the
carseat manual.
31
SE
EN
CZ
DE
DK
EE
ES
FI
NO
SVK
BG
FR
GR
HR
HU
IS
IT
LV
LT
ML
NL
PL
RO
PT
RS
RU
SL
TR