Inhaltsverzeichnis
Werbung
6) OPEN THE BUMPER BAR
6.1 Unfasten the crotch strap. Press the button
on the inside of the bumper bar and open.
7) CLOSE THE BUMPER BAR
7.1 Click the bumper bar into the bracket until
you hear a "click".
Fasten the crotch strap around the bumper bar.
WARNING
Ensure that children are kept away
from all moving parts of the pram to avoid risk
of injury.
WARNING
The bumper bar should always be
assembled when in use.
WARNING
Always check that the bumper bar is
correctly assembled before use.
8) REMOVING THE SEAT UNIT FROM THE
CHASSIS
8.1 Pull both handles upwards and lift the seat
unit off the chassis
WARNING Ensure that children are kept away
from all moving parts of the pram to avoid risk
of injury.
WARNING Never leave a child in the seat unit
when removing the seat unit.
8.2 The seat unit can be adjusted into different
positions, lift the handle at the back of the seat
unit up and adjust to desired position.
WARNING Always check that the seat unit is in
one of the positions by pushing it back until it
locks into place.
WARNING Ensure that children are kept away
from all moving parts of the pram to avoid risk
of injury.
8.3 Press both of the buttons on each side of
the frame to adjust the footrest.
Please Note! Maximum weight on the footrest
is 3kg.
WARNING Never let your child stand on the
footrest.
9) ASSEMBLY OF THE APRON (
9.1 Pull the apron over the footrest.
9.2 Fasten the apron with the press stud on the
inside of the hood.Fasten the press studs at the
back of the apron to the back of the seat unit.
IMPORTANT! The hood cannot be folded
down when the apron is permanently attached
to the hood.
Open the zip in the middle of the apron when
taking your child in or out of the pram.
10) REMOVAL OF THE SEAT UNIT FABRIC
10.1 Release the push buttons from the hood,
remove the hood from the seat frame,
WARNING The hood must always be assemb-
48
led when the pram is in use.
10.2 Unbutton the buttons and buckles on each
side.
10.3 - 10.4 open the zipper located under the
seat, remove the fabric from the seat plate.
10.5 Thread all seat belts through the holes.
10.6 Remove the push button around the
folding handle and remove the fabric from the
seat frame.
11) RAINCOVER (
11.1. Assemble the rain cover by placing it over
the hood and pull over the carrycot or the seat
unit.
11.2. The rain cover has a large window at the
top opening that you can open and close with
the Velcro fasteners.
11.3. Make sure that the side ventilation win-
dows are always open and free so that ventila-
tion is ensured.Always use rain protection when
it is raining or snowing. If the stroller is wet, try
to dry it first before using the rain cover. Let the
rain cover dry properly before putting it back in
its pocket.
5-POINT HARNESS (ERGO)
1) BUCKLE THE CHILD
1.1 Place the 5 harness straps in front of the
child so that the child is not sitting on them.
1.2 Assemble the left shoulder and waist straps
by sliding the upper left buckle into the lower
left buckle until it clicks into place.
1.3 Assemble the right shoulder and hip straps
by sliding the upper right buckle into the lower
right buckle until it clicks into place.
1.4 Click the right buckle over the left buckle
)
ACCESSORIES
until they are held together as a unit. It is very
important that they sit together properly and
that they cannot be pulled apart.
1.5 Lock the harness with the harness lock on
the crotch strap with a "" CLICK "".
WARNING
properly closed by pulling on it.
1.6 Adjust the harness using the sliding adjus-
ters (3) on the shoulder and hip belts so that the
belt fits snugly on the child's body.
To release the shoulder and waist straps, press
in the buttons on the sides of the harness lock.
WARNING
harness when the child is sitting in the stroller.
Check that all buckles are correctly fastened and
)
ACCESSORIES
Always check that the belt is
Always fasten the child in with the
NXT SELECT V1.2
Werbung
Inhaltsverzeichnis
