Technical Data; Introduction To Spraying Using The Xvlp Procedure; Coating Material; Coating Materials Suitable For Use - WAGNER FINISH CONTROL 3500 Originalbetriebsanleitung

FinishControl 3500
4

TECHNICAL DATA

The rating plate is underneath the air filter over.
Voltage:
Power onsumption:
Atomizing output:
Container volume:
Power able:
Prote tion lass:
Sound pressure level:*
Un ertainty K:
Sound pressure output:*
Un ertainty K:
Os illation level:
Un ertainty K:
Weight (motor-operated blower
and spray gun):
* The a ousti emission value was as ertained in a ordan e
with EN 50144-2-7:2000
5
INTRODUCTION TO SPRAYING
USING THE XVLP PROCEDURE
XVLP (Extra Volume Low Pressure) is a low pressure spraying
te hnique, whi h works with a high volume of air and a low air
pressure. The greatest advantage of this spraying te hnique
is the low paint mist formation. This redu es the amount re-
quired to over the obje t to a minimum.
As opposed to onventional appli ation of oatings, this
method a hieves a highly e onomi al and perfe t surfa e
quality and is, at the same time, environmentally friendly.
Function description
The paint spraying system onsists of a motor-operated tur-
bo-blower, whi h provides the spray gun with atomisation air.
In the spray gun, a part of the atomisation air is used to pres-
surise the ontainer. This pressure auses the oating material
to be fed through the uptake pipe to the nozzle where it is
TECHNICAL DATA/ INTRODUCTION/ PREPARING THE COATING MATERIAL
230 V~, 50 Hz
700 W
220 W
1000 ml
4 m
I
74 dB (A)
4 dB (A)
87 dB (A)
4 dB (A)
<2.5 m/s²
1.5 m/s²
2.3 kg
atomised by the rest of the atomisation air.
All settings ne essary for operation (e.g. material volume) an
be onveniently made, dire tly on the gun.
Field of application
The FC 3500 is designed for smaller to medium-sized proje ts,
i.e. for surfa es of a maximum of 50 m².
6

COATING MATERIAL

6.1

COATING MATERIALS SUITABLE FOR USE

Solvent-based and water-soluble la quer paints
Mordants, glazes, impregnations, oils, lear varnishes, syn-
theti enamels, oloured paints, alkyd resin varnishes, prim-
ers, radiator paints, hammer effe t enamels, anti-rust paints,
spe ial-effe t paints, textured paints
6.2

COATING MATERIALS NOT SUITABLE FOR USE

Materials that ontain highly abrasive omponents, fa ade
paint, austi solutions and a idi
Flammable materials.
6.3 COATING MATERIALS THAT CAN ONLY BE
PROCESSED WITH RELEVANT SPRAY
ATTACHMENT (ACCESSORIES)
Interior wall paint (dispersions and latex paint)
6.4 PREPARING THE COATING MATERIAL
Observe the manufa turer's instru tions for the
use of the oating material on the paint tin or on
the te hni al instru tion sheet.
Coating material purity:
An absolute pre- ondition for the trouble-free operation of
the fine-spray system is that the oating material is un on-
taminated. If you have doubts as to the purity of the oating
material, we re ommend that you first filter it through a fine
sieve.
Processing the coating material with the StandardSpray
spray attachment (yellow)
Coating Material Processing
Solvent-based la - observe manufa -
quer paints turer's instru tions
Water-soluble la - observe manufa -
quer paints turer's instru tions
GB
oating substan es.
Comments
19