Package Contents; Electrical Safety - DeWalt DW721 Anleitung

• Do not place hands closer than 150 mm from the saw blade while cutting.
• Do not use damaged or cracked saw blades.
Residual risks
The following risks are inherent to the use of radial arm saws:
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be avoided.
These are:
- Impairment of hearing.
- Risk of accidents caused by the uncovered parts of the rotating saw blade.
- Risk of injury when changing the blade.
- Risk of squeezing fingers when opening the guards.
- Health hazards caused by breathing dust developed when sawing
wood, especially oak, beech and MDF.

Package contents

The package contains:
1 Partly assembled machine
1 Motor, yoke and roller head assembly with no-volt release switch
2 Table extensions (DW721/DW722)
1 Table extension (DW725/DW726)
1 Guard assembly
2 Push sticks
1 Box containing:
1 legstand (4 legs, 4 traverse rails, 24 M8 x 16 bolts, 24 M8 nuts and
48 D8 flat washers)
1 Skinpack containing:
1 return spring
2 binding screws
1 yoke travel stop
1 dust extraction adapter
2 M5 x 16 screws
2 M5 nuts
1 cable support
1 Skinpack containing:
1 spanner 10/13/17/30 mm
1 ring/open spanner
1 box spanner 13 mm
5 Allen keys (2.5, 3, 4, 5 & 8 mm)
1 height adjustment crank
1 cross head screw
1 saw blade
1 cable clamp
4 table extension supports (DW721/DW722)
2 table extension supports (DW725/DW726)
16 M8 x 25 bolts (DW721/DW722)
8 M8 x 25 bolts (DW725/DW726)
16 D8 flat washers (DW721/DW722)
8 D8 flat washers (DW725/DW726)
8 M8 nuts (DW725/DW726)
8 D8 Belleville washers (DW725/DW726)
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior to
operation.
Description (fig. A1 & A2)
The DW721/DW722/DW725/DW726 radial arm saw has been designed for
the professional woodworking industry. This high precision machine can be
easily and quickly set to crosscut, bevel, mitre, or rip. With the help of the wide
variety of accessories, your radial arm saw will perform virtually all workshop
operations. For optimum safety, all major controls have both a latch and a
locking device. Also refer to the quick reference chart in this manual.
21
A1
1 On/off switch
2 Handle
3 Blade guard assembly
4 Fixed table top
5 Leg
6 Fence
7 Table clamp
8 Column
9 Mitre latch lever
10 Mitre clamp lever
11 Height adjustment crank
12 Radial arm
13 End-cap
A2
14 Yoke travel stop
15 Riplock
16 Yoke
17 Motor
18 Table strips
19 Table extension
20 Bevel scale
21 Roller head assembly
22 Reset button
23 Cable support

Electrical safety

The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Mains plug replacement
(U.K. & Ireland only)
• Should your mains plug need replacing and you are competent to do
this, proceed as instructed below. If you are in doubt, contact an
authorized D WALT repair agent or a qualified electrician.
E
• Disconnect the plug from the supply.
• Cut off the plug and dispose of it safely; a plug with bared copper
conductors is dangerous if engaged in a live socket outlet.
• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly
rated fuse (1).
• The cable wire colours, or a letter, will be marked at the connection
points of most good quality plugs. Attach the wires to their respective
points in the plug (see below). Brown is for Live (L) (2), blue is for
Neutral (N) (4) and green/yellow is for Earth (E).
• Before replacing the top cover of the mains plug ensure that the cable
restraint (3) is holding the outer sheath of the cable firmly and that the
leads are correctly fixed at the terminal screws.
Never use a light socket.
Never connect the live (L) or neutral (N) wires to the earth pin
marked E or .
For 115 V units with a power rating exceeding 1500 W, we recommend to
fit a plug to BS4343 standard.
E N G L I S H
en - 3