Package Contents; Description (Fig. A) - DeWalt DWE46172 Bersetzt Von Den Originalanweisungen

READ ALL INSTRUCTIONS

Package Contents

The package contains:
1 Surface grinding shroud
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.

Description (Fig. A)


WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Hose clamp screw
1
Hose clamp
2
Intake vent
3
Dust port for universal connector
4
Gear case adaptor
5
Adaptor for non-hubbed diamond wheels
6
Intended Use
Your concrete surface grinding shroud has been designed for
dust removal of the following: grinding, leveling and polishing
concrete surfaces. It can remove dust when removing surface
paint, epoxy and glue. Using the appropriate grinder, diamond
grinding wheel and dust extractor vacuum it can be used to
remove the vast majority of static and airborne dust which
without the use of the surface grinding shroud could otherwise
contaminate the working environment or pose an increased
health risk to the operator and those in close proximity. This
concrete surface grinder should ALWAYS be used with a M
class dust extractor designed for concrete dust removal, like the
D WALT DWV902M.
e
DO nOt use under wet conditions or in presence of flammable
liquids or gases.
The surface grinding shroud is a professional tool. DO nOt let
children come into contact with the tool. Supervision is required
when inexperienced operators use this tool.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of injury, ALWAYS turn
off the tool and disconnect the tool from the power
source before making any adjustments or removing
or installing attachments or accessories. This applies
to both the grinder and the dust extractor vacuum.
Such preventative safety measures reduce the risk of
starting the tool accidentally.
Mounting and Removing Surface Grinding
Shroud (Fig. B–D)
nOtE: The shroud and adaptor
grinder. Take extra care when mounting the shroud.
1. Follow the mounting and removing guard instructions
in the power tool manual to remove the existing guard
from grinder.
2. If present, remove the stop screw
grinder with a T40 star wrench.

WARNING : After removing the stop screw the grinder
cannot be used with a type 1 guard or a type 27 guard
for grinding or cutting applications. To perform these
applications stop screw MUST be put back in place.
Performing grinding and cut-off applications without
having the stop screw in place can result into death or
serious injury due to malfunction of the guarding system.
3. With the beveled edge facing upward from the shroud
collar, insert the gear case adaptor
refer to Figure C.
4. Aligning the adaptor and shroud with the gear casing, push
them both down onto the gear case with your thumbs.
You can also use a large flathead screwdriver to be sure the
adaptor is seated correctly. Both the shroud and the adaptor
should slide down onto the gear case at the same time.
5. Position shroud to desired orientation, and tighten hose
clamp screw 1 securely.
6. To remove the shroud, repeat these steps in reverse
NOTICE: If surface grinding shroud cannot be tightened
by the hose clamp screw, do not use the tool and take the
tool and surface grinding shroud to a service center to
repair or replace the surface grinding shroud.
Mounting Dry Diamond Surface Cup Wheels
(Fig. E)

WARNING: DO NOT use Type 1 cutting wheels or bonded
abrasive wheels. Damage or personal injury could result.
Follow the mounting and using cutting wheels instructions in
the tool manual and mount the grinding wheel.
Dry diamond surface cup wheels
with this shroud.
EngLIsh
5 have a tight fit onto the
from your D WALT
8
e
5 partially into the collar,
7 are recommended for use
15