Package Contents; Electrical Safety - DeWalt DW721 Anleitung

E N G L I S H
These are:
- Impairment of hearing.
- Risk of accidents caused by the uncovered parts of the rotating saw
blade.
- Risk of injury when changing the blade.
- Risk of squeezing fingers when opening the guards.
- Health hazards caused by breathing dust developed when sawing
wood, especially oak, beech and MDF.

Package contents

The package contains:
1 Partly assembled machine
5 Table top sections
1 Fence 48 mm
1 Fence 65 mm
5 Straight table supports
3 Triangular table supports
1 Height adjustment crank
1 Motor, yoke and roller head assembly with no-volt release switch
1 Bracket for no-volt release switch
1 Saw blade
1 Guard assembly
1 Dust extraction adapter
1 Box containing:
1 legstand (4 legs, 4 traverse rails, 24 M8 x 16 bolts, 24 M8 nuts and
48 D8 flat washers)
1 Set of parts for table extension:
8 M8 x 30 flat slotted head bolts
8 D8 Belleville washers
8 M8 nuts
8 D8 flat washers
1 Skinpack containing:
3 spanners (30, 10/13 & 17 mm)
1 ring/open spanner
1 box spanner 13 mm
5 Allen keys (2.5, 3, 4, 5 & 8 mm)
1 cross head screw
8 M8 x 30 screws
6 M8 screws
14 M8 nuts
1 cable clamp
1 cable support
2 selftapping screws
2 M4 nuts
2 table clamps
2 clamps for return spring
14 D8 Belleville washers
8 D8 flat washers
1 Skinpack containing:
9 D8 flat washers
19 Belleville washers
19 M8 nuts
10 M8 x 30 flat slotted head bolts
9 M8 x 16 flat slotted head bolts
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior to
operation.
• Remove the saw from the packaging material carefully.
en - 3
Description (fig. A1 & A2)
The DW721 free-standing Radial Arm Saw has been designed for the
professional woodworking industry. This high precision machine can be
easily and quickly set to crosscut, bevel, mitre, or rip. With the help of the
wide variety of accessories, your Radial Arm Saw will perform virtually all
workshop operations. For optimum safety, all major controls have both a
latch and a locking device. Also refer to the quick reference chart in this
manual.
A1
1 ON/OFF-switch
2 Handle
3 Blade guard assembly
4 Fixed table top
5 Leg
6 Fence
7 Table clamp
8 Column
9 Mitre latch lever
10 Mitre clamp lever
11 Height adjustment crank
12 Radial arm
13 End-cap
A2
14 Yoke travel stop
15 Riplock
16 Yoke
17 Motor
18 Table strips
19 Table extension
20 Bevel scale
21 Roller head assembly
22 Reset button
23 Cable support

Electrical safety

The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Mains plug replacement (U.K. & Ireland only)
• Should your mains plug need replacing and you are competent to do
this, proceed as instructed below. If you are in doubt, contact an
authorized D WALT repair agent or a qualified electrician.
E
• Disconnect the plug from the supply.
• Cut off the plug and dispose of it safely; a plug with bared copper
conductors is dangerous if engaged in a live socket outlet.
• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly
rated fuse (1).
• The cable wire colours, or a letter, will be marked at the connection
points of most good quality plugs. Attach the wires to their respective
points in the plug (see below). Brown is for Live (L) (2) and Blue is for
Neutral (N) (4).
• Before replacing the top cover of the mains plug ensure that the cable
restraint (3) is holding the outer sheath of the cable firmly and that the
two leads are correctly fixed at the terminal screws.
24