Optional Accessories - DeWalt DW721 Anleitung

E N G L I S H
• Hold the workpiece against the fence, keeping your fingers well away
from the path of the blade.
• Switch ON and slowly pull the blade though the fence and the
workpiece.
• Return the blade to rest position and switch OFF.
Mitre cuts (fig. A1 & L3)
• Release the mitre latch lever (9) and the mitre clamp lever (10) (fig. A1).
• Swing the arm to the required angle on the mitre scale.
• For 45° left or right, engage the mitre latch lever (9) and lock with the
mitre clamp lever (10).
• For intermediate angles, use the mitre clamp lever only.
• Proceed as for cross-cutting.
In the case of left-hand mitre, you may have to slide the fence
and the strips to the left.
Bevel cuts (fig. A1, E2 & L2)
• Set the arm as for a 0° cross-cut.
• Raise the blade well above the table surface.
• Release the bevel clamp lever (37) and pull out the bevel latch (38) (fig. E2).
• Tilt the motor to the required angle on the bevel scale (20) (fig. A1).
• For 90° or 45° right, engage the bevel latch (38) and lock with the bevel
clamp lever (37).
• For intermediate angles, use the bevel clamp lever only.
• Proceed as for a vertical cross-cut.
Ripping (fig. L5, G2, H1 & H2)
The motor can be locked in in-rip or out-rip position as shown in figures
H1 & H2 to adapt the machine to narrow and wide workpieces
respectively.
• Lock the yoke in pulled out position using the riplock.
• Release the yoke clamp lever (53) and press the yoke latch (54) to
rotate the motor to the appropriate position until it locks in place (fig. H1).
• Tighten the yoke clamp lever (53) and position the fence accordingly.
• Position the yoke along the arm for the desired width of cut, using the
rip scale (76) and lock it in position using the riplock.
• Adjust the blade guard as described above and turn the dust extraction
adaptor (59) away from your face (fig. G2). Remember that ripping
requires the use of the riving knife (62) and the anti-kickback fingers (60)
(fig. H2).
• Slowly feed the workpiece into the blade, keeping it firmly pressed onto
the table and against the fence. Allow the teeth to cut and do not force
the workpiece through the blade. The blade speed should be kept
constant.
Always use a push stick.
Bevel ripping
• Set the machine in the bevel crosscut position.
• Rotate the yoke into rip position.
• Position the yoke for the correct ripping width.
• Angle the anti-kickback fingers so that they will be flat on the
workpiece and lower the riving knife.
• Proceed as for ripping.
Compound mitre (fig. L4)
This cut is a combination of a mitre and a bevel cut.
• Set the required bevel angle.
• Swing the arm to the required mitre position.
• Proceed as for mitre cuts.
Always switch OFF the tool when work is finished and before unplugging.
en - 7
Coving/hollowing
Your radial arm saw can be used for a wide variety of advanced
applications, such as coving/hollowing.
• Tilt the blade to the required angle, rotate the yoke beneath the arm
and position the blade above the workpiece where required. Remove
the workpiece and lower the blade to make a shallow cut. Lower the
anti-kickback fingers as for bevel ripping. Keeping the workpiece
against the fence, proceed as for ripping.
Make shallow cuts only!
Dust extraction (fig. G2)
The machine is provided with a dust extraction adaptor (59).
• Whenever possible, connect a dust extraction device designed in
accordance with the relevant regulations regarding dust emission.
• When cross-cutting, position a dust collection shute (option) behind the
line of cut.

Optional Accessories

Prior to assembling any accessories always unplug the machine.
Shaping/moulding head
The shaping/moulding head is used to provide your work with a
professional finish.
Mounting the shaping/moulding head (fig. M1 - M3)
• Remove the blade guard assembly and the blade.
• Fit the cutters (89) to the shaping/moulding head (90), making sure that
they are both installed in the same way (fig. M1).
• Mount the special spacer (91) supplied with the shaping head onto the
arbor.
• Put the shaping head onto the arbor as shown and lock it with the
clamping nut (92) using the box spanner (93) available as an option.
• Tilt the motor until the shaping head is in horizontal position.
• Mount the shaping head guard (94) (fig. M2) as shown and adjust it to
the required depth of cut (fig. M3).
Shaping/moulding
• Place the shaping/moulding head over the fence. The protruding
section corresponds to the cut that will be made.
Certain applications may require to divide the fence into two sections and
to place the shaping/moulding head between them. In that case, the fence
must be replaced when the saw is used for ordinary applications again.
Always use a push stick.
• Feed the material firmly and evenly along the fence from the right.
Rebating
• Use straight-edged cutters.
• Proceed as for shaping/moulding.
• For bevelled rebate cutting, tilt the motor to the required angle.
For wider rebates, use the dado head together with the guard
of the shaping/moulding head.
Refer to the instructions pertaining to the use of the dado head.
28