Unpacking; Assembly - Scheppach WSE5000-Multi Bedienungsanleitung

LIFT TIG welding
Off-load voltage U
0
Working voltage U
2
Welding current l
2
Highest mains current
rated value
max
Effective value of the
largest mains current
eff
Energy efficiency of the
power source
Power consumption in
idle state
Duty cycle X
20%
60%
100%
Technical changes reserved!
7.

Unpacking

• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be
recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating instructions before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Replace-
ment parts can be obtained from your dealer.
• When ordering please provide our article number as
well as type and year of manufacture for your equip-
ment.
M WARNING!
The device and the packaging material are not
children's toys! Do not let children play with plas-
tic bags, films or small parts! There is a danger of
choking or suffocating!

8. Assembly

76 V~
Mounting the welding mask (Fig. 3 + 4)
10.4 - 18 V~
Fit the handle (b) to the welding mask (c).
10 - 200 A
Fit the protective glass (a) to the welding mask (c).
26.8 A
Then fold the three sides of the welding mask together.
The two side parts are connected to the top part by two
12 A
press studs.
81%
Attaching the hose assembly (Fig. 5 + 6)
Insert the hose assembly (27) into the connection (8)
20 W
and screw it tight.
Installing the welding wire reel (Fig. 7 - 10)
200 A
• Open the cover for the wire feeding device by push-
117 A
ing the lock (d) upwards.
90 A
Now you can see the wire feeding device and the
welding wire reel (Fig. 8 - 9).
• Unlock the reel mounting (f).
• Remove all packaging from the wire reel so that it
can unroll freely.
• Fit the wire reel onto the reel mounting. Ensure that
the reel will unwind on the same side as the wire
guide (g).
• Now press the adjustment screw (h) downwards and
fold the pressing roller (j) upwards. (Fig. 9)
• Unscrew cover (i) to check the feed roller.
• The corresponding wire thickness is marked on the
top side of the feed roller. If the size stipulated there
does not match with the actual wire thickness, turn
the feed roller or replace it if necessary.
• Now take the wire end off the edge of the reel and
trim it with side cutters or wire shears. Ensure that
the wire does not unroll.
• Now feed the wire through the wire guide (g) along
the feed roller and into the hose assembly fitting
(Fig. 9).
• Tension the pressing roller (j) again.
• Remove the burner nozzle (m) by simply pulling it off.
Unscrew the contact tip (l) too.
• Route the hose assembly (27) as straight as possi-
ble as it runs away from the welding machine.
• Switch the welding machine on by setting the on/off
switch (2) to the "ON" position.
• Now press the burner button (28) to activate the wire
feed. Press the button until the wire emerges from
the front of the burner. When doing so, pay attention
to the feed roller. If this is slipping, re-tension the
pressing roller (j) with the adjustment screw (h).
Do not touch the welding wiring during this pro-
cedure as there is a risk of injury with this!
www.scheppach.com GB | 33