Technical Data; Attachment And Operation - Scheppach Special Edition HL 1400 Originalbetriebsanleitung

Electrical safety
Never use the machine if there is any risk of an
electrical hazard. Never use an electrical device in
moist conditions. Never use this machine with an
unsuitable cable or extension cable. Never use this
machine if you are not connected to a properly earthed
connection which provides the power required as
specified on the label and is protected by a 16 amp
fuse.
Mechanical hazards
Wood splitting is associated with particular mechanical
hazards. Never use this machine if you are not
wearing proper safety gloves, shoes with steel caps
and certified eye protection. Be cautious of splinters
generated while working; avoid stab-like injuries and
the possibility of the machine seizing up. Never attempt
to split any trunks which are either too long or too small
and do not fit in the machine properly. Never attempt
to split any trunks which contain nails, wire or any
other objects. Clear up while you work; collections of
split wood and wood chips can make your work area
dangerous. Never continue working if your work area
is full to the extent that you could slip, trip or fall over.
Keep onlookers well away from the machine and never
permit unauthorized persons to operate the machine.
m Remaining hazards
The machine has been built using modern technology
in accordance with recognized safety rules. Some
remaining hazards, however, may still exist.
The splitting tool can cause injuries to fingers and
hands if the wood is incorrectly guided or supported.
Thrown pieces can lead to injury if the work piece is not
correctly placed or held.
Injury through electric current if incorrect electric
connection leads are used.
Even when all safety measures are taken, some
remaining hazards which are not yet evident may still
be present.
Remaining hazards can be minimized by following the
safety instructions as well as the instructions in the
chapter Authorized use and in the entire operating
manual.
Danger due to particular properties of the log
(branches, irregular shape etc)
All manuals and user guides at all-guides.com

6. Technical data

HL1400
Technical data
Dimensions D/W/H
Table height mm
Working height mm
Log length cm
Power tons*
Piston stroke cm
Forward speed cm/s
Return speed cm/s
Oil quantity litres
Log width min./max. cm
Weight kg
Drive
Motor V/Hz
Input P1 kW
Output P2 kW
Operating mode
Protection class
Motor speed 1/min
Motor protection
Phase inverter
Technical changes subject to change!
* The maximum achievable splitting power depends on the
resistance of the material to be split and can, due to influencing
variable, deflect to the hydraulic system.
Information concerning noise emission measured
according to relevant standards:
Sound pressure L = 77 dB(A)
pA
Sound power L = 88 dB(A)
wA
Uncertainty K = 3 dB(A)
pA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration A (Griff) = 2,5 m/s
2
hv
Uncertainty K = 1,5 m/s
2
pA

7. Attachment and operation

Setting up
Prepare the work place where the machine is to stand.
Create sufficient space in order to allow safe working
without disturbance.
The machine has been designed for working on a level
surface. It must therefore be set up in a stable position
on firm ground.
Assembly
Please make sure the assembled parts are firmly
tightened.
Before putting the appliance into operation, check
it for the following:
• Cable not damaged
• Perfect state of the protection and cutting equip-
ment
• Firm tightening of all the screwing
For reasons of packing, your Scheppach log splitter is
not completely assembled.
Fitting the operating arms, Fig. 4
Fix the protection bow (B) by using the countersunk
head screw (B.1,cross recess).(shown in Fig.2.1)
Fix now the fixing sheets (A) by using 1 screw, washer
and nut (A.1).(shown in Fig.2.1)
1190/800/1580
800/540/70
920
59/88/135
14
50
4,5
11,0
10
12 – 40
190
400/50
4,3
3,2
S6/40 %
IP 54
1495
yes
yes
GB 22