Technical Data; Unpacking; Attachment / Before Starting The Equipment - Scheppach HL810 Original Bedienungsanleitung

• Thrown pieces can lead to injury if the work piece
is not correctly placed or held.
• Injury through electric current if incorrect electric
connection leads are used.
• Even when all safety measures are taken, some
remaining hazards which are not yet evident may
still be present.
• Remaining hazards can be minimized by following
the safety instructions as well as the instructions in
the chapter Authorized use and in the entire oper-
ating manual.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Release the handle button and switch off the ma-
chine prior to any operations.
• Avoid accidental starts of the machine: Do not
press the start button while inserting the plug into
the socket.
• Use the tools recommended in this manual to ob-
tain the best results from your machine.
• Always keep hands away from the work area when
the machine is running.

7. Technical data

Motor
Input P1
Output P2
Operating mode
Motor speed
Dimensions D/W/H
Table height
Working height
Log length
Power max.
Piston stroke
Forward speed
Return speed
Oil quantity
Weight
Subject to technical changes!
* Operating mode S6 40% is an uninterrupted, peri-
odic mode. The mode comprises of a start-up period,
a time with constant load and an idle time. The oper-
ating time is 10 mins, the relative duty cycle is 40% of
the operating time.
Noise
m Warning: Noise can have serious effects on your
health. If the machine noise exceeds 85 dB (A),
please wear suitable hearing protection.
230 V∼ / 50 Hz
3000 W
2200 W
S6 40%
2800 1/min
845 x 935 x 1500 mm
800 mm
940 mm
550 mm
8 t*
550 mm
3,1 cm/s
17,3 cm/s
4 l
109,9 kg
www.scheppach.com
Noise data
Sound power level L
WA
Sound pressure level L
pA
Uncertainty K
WA/pA

8. Unpacking

Open the packaging and remove the device carefully.
Remove the packaging material as well as the pack-
aging and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for transport
damage.
In case of complaints the dealer must be informed
immediately. Subsequent complaints will not be ac-
cepted.
If possible, store the packaging until the warranty pe-
riod has expired.
Read the operating manual to make yourself familiar
with the device prior to using it.
Only use original parts for accessories as well as for
wearing and spare parts. Spare parts are available
from your specialized dealer.
Specify our part numbers as well as the type and year
of construction of the device in your orders.
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
9. Attachment / Before starting the
equipment
9.1 Fitting the wheels (7) (accessories bag A)
• Insert the bolt through the wheel.
• Attach two washers.
• Now insert the bolt through the holes in the lower
part of the splitter (fig. 3).
• Now fix the bolt with a washer and a cotter pin.
• Finally fit the small wheel cap
• Repeat this process on the other side.
9.2 Fitting the table (5)
• Undo the star-grip screw (Fig. 4)
• Now fold out both side trays (11), as shown in Fig. 5
• Now fit the table in the retainer intended (Fig. 6 (1)
and re-tighten the star grip screws previously loos-
ened (Fig. 6 (2).
9.3 Fitting the complete control arms (10)
(accessories bag B)
• Remove pre-assembled bolt (fig. 7 (C).
• Grease the top and bottom plates.
• Insert the complete control arm in the position pro-
vided (fig. 7 (1).
93,6 dB(A)
77,8 dB(A)
3 dB
GB | 21