Storage; Transport; Disposal And Recycling - Scheppach SG2000 Originalbetriebsanleitung

Check, clean and replace spark plug
Check the spark plug after 10 hours on dirt and grime.
If necessary, clean it with a copper wire brush. Main-
tenance the spark plug after 50 hours of operation
• Open the spark plug cover (Fig. 12 + 13)
• Remove the ignition cable with plug. (Fig. 14 Pos. I)
• Remove any dirt from the base of the spark plug.
• Use a wrench to remove the spark plug (Pos. H).
• Check the spark plug visually. Remove any debris
with a wire brush.
• Look for discoloration on the top of the spark plug.
By default, the color should be bright.
• Check the spark plug gap. An acceptable gap width
is 0.6 to 0.7 mm (Fig. 15)
• Remove the spark plug carefully by hand.
• If the plug has been inserted, tighten them with a
spark plug wrench.
• Attach the spark plug wire with connector on the
spark plug.
Note
A loose spark plug can overheat and damage the en-
gine. And overtightening the spark plug can damage
the threads in the cylinder head.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: spark plug
* Not necessarily included in the scope of delivery!
Cleaning
• Keep all safety devices, air vents and the motor
housing free of dirt and dust. Wipe the equipment
with a clean cloth or clean it with compressed air at
low pressure.
• We recommend that you clean your device after
each use.
• Clean the unit regularly with a damp cloth and some
soft soap. Do not use cleaning agents or solvents;
they may damage the plastic parts of the appliance.
Make sure that no water can get inside the unit.

10. Storage

1. Perform all general maintenance, which are in the
User's Guide in the Maintenance section.
2. Let the fuel out of the tank (Use a commercially
plastic fuel pump from the hardware store).
3. After the fuel is drained, start the machine.
4. Let the machine in idlespeed running until it stops.
That cleans the carburetor from the remaining
fuel.
5. Let the machine cool down. (about 5 minutes)
6. Remove the spark plug.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
7. Fill a small amount of 2-stroke engine oil into the
firing chamber. Pull out several times the starter
cord gently to wet the internal components with
the oil.
8. Replace the spark plug.
9. Clean the outer casing of the machine.
10. Keep the machine on a cold, dry place out of reach
of ignition sources and flammable substances.
Recommissioning
1. Remove the spark plug.
2. Pull the starter rope out several times. It cleans
the firing chamber of oil residues.
3. Clean the spark plug contacts or install a new
spark plug.
4. Fill the tank.

11. Transport

m WARNING
Let the engine cool down before transporting the ma-
chine or storing indoors to avoid burns or fire hazards.
If you want to transport the unit empty the fuel tank
before. Clean the unit with a brush or a broom of
coarse dirt.

12. Disposal and recycling

The disposal instructions are based on icons placed
on the appliance or its package. A description of the
individual meanings, is shown in chapter "Explana-
tion of symbols on the device".
Transport package disposal
The package protects the appliance against damage
during transport. Packing materials are usually cho-
sen depending on their environmental friendliness
and disposal method and can therefore be recycled.
Returning the package to material circulation saves
raw materials and reduces waste disposal costs.
Parts of packages (e.g. foils, styropor®) can be dan-
gerous to children.Risk of suffocation! Keep parts of
packages away from children and dispose them as
soon as possible.
24 | GB