Regeneration Process For Vehicles With A Diesel Particle Filter (Dpf) - Kärcher MC 130 Plus Bedienungsanleitung

Sweeping with a 2-brush system
Left joystick
1
2-brush system: Lower the brush arms and switch on the
brushes
3-brush system (option): Lowering/raising the 3rd brush and
switching the brush on/off
Right joystick
2
With the optional 3-brush system: Lowering/raising the 2 rear
brushes and switching the brushes on/off
Pivoting the brushes in and out
Raise/lower suction mouth
3
Hydraulic system on/off
4
With the optional 3-brush system: Brush reversal of the 3rd
5
brush
With the optional 3-brush system: Inclining/rolling the 2rd
6
brush
Note
Operation with the right-hand joystick
Water circulation function on/off
7
Suction fan on/off
8
Note
The suction fan has an afterrun time of approx. 15 seconds after
being switched off
"eco" e function
9
Switches the complete work program on.
PTO, side brush, suction fan, fresh water, water circulation
(recycling water)
Water pump on/off
10
Note
The indicators in the switches light when the switches are
switched on.
1. Start the engine, see chapter Start motor.
2. Switch on the hydraulic system.
3. Set the desired engine speed.
4. Switch on lower suction mouth.
5. Set the side brush speed.
6. Switch on the suction fan.
7. Move the left-hand joystick forwards.
The right and left brush arms are lowered and the brushes are
switched on
Adjust the sweeping width.
8. Move the right-hand joystick forwards.
The right side brush lowers and is switched on.
Adjust the sweeping width (optional).
When brushing dry, dusty waste:
9. Switch on the water pump.
Optional: Switch on the water circulation function if necessary.
Emptying the waste container
CAUTION
Risk of tilting
Only empty the waste container on a firm even subsurface.
Maintain the safety distance while emptying on dumps or ramps.
82
CAUTION
Danger due to rolling away
Set the travel direction lever to neutral for emptying.
Apply parking brake.
CAUTION
Danger of injury
Switch off the suction fan before emptying the waste container.
CAUTION
Risk of injury
During the emptying process, persons and animals must not
abide within the swivelling range of the waste container.
CAUTION
Crush hazard
Never reach into the rod assembly for the emptying mechanism.
1. Stop the vehicle.
2. Apply the parking brake.
3. Bring the travel direction lever into the neutral position (middle
position).
4. Set the switch lever to the "Waste container" position.
5. Switch on the PTO.
6. Lift the right side brush and switch it off by moving the left joy-
stick to the right and then pushing it back.
7. Lift the right side brush by moving the right joystick to the left
and then pushing it back.
8. Switch off the water pump.
9. Wait 20 seconds.
10.Switch off the suction fan.
11.Actuate the toggle switch.
12.Empty the waste container.
Note
Always raise the waste container fully to the end position.
Regeneration process for vehicles with a diesel
The DPF collects soot particles that are burned off by increasing
the emission temperature when the filter is clogged (regenera-
tion).
The regeneration process runs either automatically during work-
ing mode or driving mode but can also be started manually if re-
quired.
The higher the speed when driving, or the greater the load, the
less frequent the need for manual regeneration.
In this mode the engine control unit controls the regeneration in-
dependently. A symbol is displayed in the upper symbol bar of the
display when the regeneration process is being performed. The
tool key in the service menu is used for switching between Auto-
matic and Manual regeneration.
With Manual regeneration, the driver decides when the Diesel
particle filter (DPF) regenerations process is performed. There
are 5 stages for this.
Manual regeneration - stage 1
Stage 1 is triggered when the DPF has collected the maximum
quantity of fine dust. A corresponding warning is emitted. If the
driver has activated Automatic regeneration then this is started.
A symbol is displayed in the upper symbol bar of the display.
Manual regeneration - stage 2
A flashing symbol is displayed in the upper symbol bar of the dis-
play when Automatic generation has not been performed or the
engine control unit cannot perform this.
Either automatic regeneration or "Parked regeneration" can be
activated.
Manual regeneration - stage 3
A warning symbol in the upper symbol bar of the display notifies
the driver that regeneration should be started immediately. Auto-
matic regeneration is disabled, only "Parked regeneration" is per-
mitted.
English
particle filter (DPF)
Automatic regeneration
Manual regeneration