Operation - Scheppach HS100S Originalanweisung

After each new adjustment it is advisable to carry out
a trial cut in order to check the set dimensions.
9.3 Setting the angle (fig. 14)
With the table saw you can make diagonal cuts to the
left oriented to the stop bar from 0 ° to 45 °.
m Check before each cut, that between the stop bar
(27), cross-stop (7) and the saw blade (3) a collision
is not possible.
- Undo the fixing handle (13).
- Set the desired angle on the scale by pressing and
turning the hand wheel (12).
- Lock the fixing handle (13) again in the required an-
gle position.
9.4 Working with the rip fence
9.4.1 Setting the stop height (figs. 15 - 16)
- The stop rail (27) of the rip fence (15) has two guide
surfaces with different heights.
- Depending on the thickness of the material to be
cut, the stop rail (27) as shown in fig. 16 must be
used for thick material (about 25 mm workpiece
thickness) and that shown in fig. 15 for thin material
(less than 25 mm workpiece thickness).
9.4.2 Turning the stop rail (figs. 15 - 16)
- Loosen the wing nuts (28) first for rotating the stop
rail (27).
- Now, the stop rail (27) can be removed from the
guide rail (29) and pushed over it again using the
corresponding guide.
- Tighten the wing nuts (28) again.
- The stop rail (27) can be applied to the left or right
of the guide rail (29) as needed. To this end, only
install the bolts from the other side of the guide rail
(29).
9.4.3 Setting the cutting width (fig. 17)
- The rip fence (15) must be used for longitudinal cut-
ting of wood parts.
- The rip fence (15) should be mounted on the right
side of the saw blade (3).
- Set the rip fence (15) on top of the guide rail for rip
fence (14).
- On the guide rail for rip fence (14), there are 2
scales which indicate the distance between the rip
fence (15) and the saw blade (3).
- Select the appropriate scale depending on whether
the stop rail (27) is rotated for processing thick or
thin material:
High stop rail (thick material):
Low stop rail (thin material):
- Set the rip fence (15) to the desired level in the sight
glass and fix it with the eccentric lever for the rip
fence (30).
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
- When mounting or adjusting the rip fence, ensure
that the rip fence is aligned parallel to the saw
blade.
9.5 Transverse stop (fig. 18)
- Push the transverse stop (7) into a groove (31a/31b)
of the saw bench.
- Loosen the handle screw (32).
- Turn the cross stop (7) until the desired angle is
set. The arrow on the transverse stop is at the set
angle. (0°-60°)
- Tighten the knurled screw (32) again.
- The stop rail (34) can be moved on the transverse
stop (7). Loosen the nuts (33) and push the stop
rail (34) to the desired position. Tighten the nuts
(34) again.
Caution!
- Do not push the stop rail (34) too far towards the
saw blade.
- The distance between the stop rail (34) and saw
blade (3) should be about 2 cm.

10. Operation

Working instructions
After each new adjustment it is advisable to carry out
a trial cut in order to check the set dimensions.
After switching on the saw, wait for the blade to reach
its maximum speed of rotation before commencing
with the cut..
Secure long workpieces against falling off at the end of
the cut (e.g. with a roller stand etc.)
Take extra care when starting the cut!
Never use the equipment without the suction function.
Regularly check and clean the suction channels..
Suitability of the saw blades:
- 24 teeth: soft materials, large chip depth, coarse cut
profile
- 48 teeth: hard materials, small chip depth, fine cut
profile
10.1 Making longitudinal cuts (fig. 19)
Longitudinal cutting (also known as slitting) is when
you use the saw to cut along the grain of the wood.
Press one edge of the workpiece against the parallel
stop (15) while the flat side lies on the saw table (1).
The blade guard (4) must always be lowered over the
workpiece.
When you make a longitudinal cut, never adopt a
working position that is in line with the cutting direc-
tion.
- Set the parallel stop (15) in accordance with the
workpiece height and the desired width. (See 9.4)
- Switch on the saw.
GB | 33