Using The Saw - Scheppach HS100S Originalanweisung

8.2 Mounting rack (figs. 6 - 7.1)
1. Screw the four support legs (16) together with the
support struts (22) onto the saw with the hex bolts
(19) (fig. 6). For this use the saw blade key (21a),
part of the delivery contents (fig. 6).
2. Now place the rubber feet (16a) onto the support
legs (16) (fig. 6.1).
3. Now, screw the long centre brace (17) and the
short centre brace (18) onto the legs (16) using
the hexagon head bolts (19) and the hexagon
head nuts (20). Make sure that the same braces
face each other. The long centre braces (17 -
marked „B") must be mounted parallel to the
operator's side of the saw. (Fig. 7).
4. Using two hex bolts (19) on each, loosely secure
the hex nuts (20) at the drill holes of the rear sup-
port legs of the support frame (16b) (fig. 7.1).
Attention!
Both support frames must be fastened to the
back of the machine!
5. Then, tighten all the nuts and bolts of the under-
frame.
8.3 Setting / mounting the riving knife
(figs. 8 - 10)
m The setting Caution! Pull out the main
plug!
The setting of the riving knife (6) must be
checked prior to commissioning. of the riv-
ing knife (6) must be checked prior to com-
missioning.
1. Set the saw blade (3) to the max. cutting depth,
bring it to the 0° position and lock it.
2. Unfasten the bolt (23) from the bench insert (2)
using a Phillips screwdriver, and remove bench
insert (2) (fig.8).
3. The distance between the saw blade (3) and the
riving knife (6) must be max. 5 mm. (fig. 9)
4. Loosen the mounting bolt (24) in order to pull
out the splitting wedge (6) until the right dis-
tance is adjusted (fig. 10).
5. Tighten the mounting screw (24) again and
mount the bench insert (2).
8.4 Mounting / dismounting the saw blade guard
(figs. 11 - 12)
1. Mount the saw blade guard (4) together with the
bolt (25) on top of the riving knife (6), so that the
bolt is firmly seated in the slot of the riving knife
(6).
2. Do not screw in the bolt (25) too tightly; the saw
blade guard (6) must move freely.
3. Plug the suction hose (5) onto the suction adapter
(26) and the connecting piece of the saw blade
guard (4). Connect a suitable splint collector onto
the suction adapter (26).
4. Disassembly is performed in reverse order.
32 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Caution!
The saw blade guard (4) must be lowered onto
the workpiece before starting the sawing op-
eration.
8.5 Replacing the bench insert (fig. 8)
1. In case of wear or damage, the bench insert
(2) must be replaced; otherwise, there is an in-
creased risk of injury.
2. Unfasten the bolt (23) using a Phillips screw-
driver.
3. Take out the worn bench insert (2).
4. The installation of the new bench insert is done
in reverse order.
8.6 Installing / replacing the saw blade (fig. 13)
1. Caution! Pull out the main plug and wear safety
gloves.
2. Dismount the saw blade guard (4) (see 8.4)
3. Remove the bench insert (2) (see 8.5)
4. Loosen the nut by placing a saw blade spanner
(22a) on the nut while holding up another saw
blade spanner (22b) on the motor shaft (see fig.
22).
5. Caution! Turn the nut in the direction of rotation
of the saw blade.
6. Remove the outer flange and remove the old
blade inner flange.
7. Clean the saw blade flange thoroughly with a wire
brush before mounting the new saw blade.
8. Insert the new saw blade in reverse order and
tighten.
Caution! Note the direction of run, the cutting
slope of the teeth must be in the direction of
run, i.e. facing forward.
9. Remount and adjust the bench insert (2) and saw
blade guard (4) (see 8.4 and 8.5)
10. Before you start working again with the saw,
check proper functioning of the safety equipment.
11. After fitting, check that the saw blade guard (4)
is functioning properly. Lift the saw blade guard
and then release it. The saw blade guard should
automatically move back to its starting position.

9. Using the saw

9.1 On/Off switch (fig. 14)
- The saw can be switched on by pressing the green
pushbutton „I". (11)
- The red pushbutton „0" (11) has to be pressed to
switch off the saw.
9.2 Cutting depth (fig. 14)
Turn the round handle (12) to set the blade (3) to the
required cutting depth.
- Anticlockwise: smaller cutting depth
- Clockwise: larger cutting depth