Safety Instructions For Transportation; Care And Maintenance; Precommissioning; Unloading Instructions - Kärcher KM 85/50 W Bp Originalbetriebsanleitung

ATTENTION ● Adhere to the operating instruction of the manu-
facturer of the battery and charger. Adhere to the recommenda-
tions of the legislature regarding the handling of batteries.
● Never leave batteries in a discharged state. Charge batteries
again as soon as possible. ● Keep batteries clean and dry in or-
der to avoid leakage currents. Protect batteries from contamina-
tion, e.g. from metal dust. ● Dispose of used batteries in an
environmentally friendly manner in accordance with the EC Di-
rective 91/157/EEC or the respective national regulations.

Safety instructions for transportation

CAUTION
● In order to prevent accidents or injuries, you must take into ac-
count the weight of the device, see chapter Technical data in
the operating instructions.
● Shut the motor down prior to transportation. Secure the device,
taking into account its weight. See chapter Technical data in the
operating instructions.

Care and maintenance

WARNING ● Disconnect the battery before working on the
electrical system. ● Switch off the device and pull the key out of
the key-operated switch before cleaning, performing mainte-
nance, replacing parts or changing to a different function.
CAUTION ● Repairs may only be carried out by approved
customer service sites or staff qualified in this area who are famil-
iar with all relevant safety instructions.
ATTENTION ● Adhere to the safety inspection requirements for
mobile devices for industrial use in accordance with the locally
applicable regulations (e.g. in Germany: VDE 0701). ● Short-cir-
cuits or other damage. Do not clean the device with a hose or
high-pressure water jet. ● Always wear suitable gloves when
working on the device.

Precommissioning

Unloading instructions

DANGER
Risk of accidents when unloading the device
Use a suitable ramp when unloading the device.
Do not use a forklift to unload / load the device.
Be aware of the weight of the device when unloading / loading.
See also the chapter "Technical data".
Figure: Build a ramp
1. Connect the battery and charge if necessary.
2. Fit the push handle and lever.
3. Use the enclosed boards to build a ramp according to the
sketch.
18
4. Cut the plastic packing strips and remove the film.
5. Remove the strap fastening at the attachment points.
6. Unscrew the three marked floor boards and the squared tim-
ber on the pallet.
7. Position the boards on the edge of the pallet; align the boards
so that they lie in front on the wheels on the device. Screw the
boards tight.
8. Place the squared timber under the boards as a support.
9. Remove the wooden blocks locking the wheels.
10.Release the parking brake.
11.Carefully drive the device off the pallet via the ramp or push it
off the pallet (see chapter "Moving the device without its own
drive").

Mount the push handle and hand lever

Note
The push handle is removed and placed in the packaging on de-
livery of the device. This must be mounted on the device.
The hand levers for the brake and the coarse dirt flap are not yet
installed and must be attached to the push handle. Adjustments
do not need to be made, these are already set correctly at the fac-
tory.
Push handle
1
Star screws (2x)
2
Coarse dirt flap hand lever
3
Brake hand lever
4
Sheathed cable clips (2x)
5
1. Fasten the push handle with the star screws.
2. Fasten the hand lever for the coarse dirt flap on the left in the
travel direction and the hand lever for the brake on the right on
the push handle as shown in the figure.
3. Fix both sheathed cables with the clips on the push handle.

Opening/closing/removing the cover

CAUTION
Risk of crushing fingers
Only use the recessed grip provided to open and close the cover.
ATTENTION
Risk of burns from a hot drive motor
The drive motor can get hot during operation.
Do not touch hot surfaces. Pay attention to the warning symbols.
Note
It is necessary to open or remove the cover:
1 To connect / install the batteries.
2 for maintenance and cleaning work.
3 To readjust the side brushes.
Note
The device will not move if the device cover is not completely
closed, (cover switch).
English