Custom Code Setting; Switching The Upper Limit Of Cooling Temperature; Dip Switch Setting; Function Setting - Fujitsu AIRSTAGE ASYE07GACH Installationsanleitung

Example
If 4 indoor units are connected.
Indoor unit
RC AD SW
0
Remote
controller
RC AD SW
Address
RC AD SW
Address
ii) 2-wire type
Rotary switch (RC AD SW)...Factory setting "0"
Since the remote controller address settings are automatically confi gured, you do not
need to confi gure them.
If confi guring manually, it is necessary to confi gure both the indoor unit and the
remote controller. For details, please refer to the remote controller manual.

6.2. Custom code setting

Selecting the custom code prevents the indoor unit mix-up.
(Up to 4 codes can be set.)
Perform the setting for both the indoor unit and the remote controller.
Indoor
unit
Remote
controller
Custom code setting for indoor unit
Set the DIP switch SET 3 SW1, SW2 referring to the Table B.
DIP switch (SET 3)
OFF
SW1
SW2
SW3
SW4
Table B
DIP switch SET 3
SW1
DIP switch SET 3
SW2

6.3. Switching the upper limit of cooling temperature

This setting can be raised the upper limit of the cooling temperature setting range.
This setting can be used when connecting to the following controllers.
• Wired remote controller (2-wire type)
• Central remote controller
• Touch panel controller
• System controller
• Service tool
• Web monitoring tool
En-9
9377773098-01_IM.indb 9 9377773098-01_IM.indb 9
Downloaded from www.Manualslib.com
Indoor unit Indoor unit
RC AD SW RC AD SW
1 2
0 1 2 3 4 5
0 1 2 3 4 5
8 9 A B C D
8 9 10 11 12 13
Code change
Confusion
A B C
A B C
ON
SET 3
Custom code
A (Factory setting) B
OFF ON
OFF OFF
manuals search engine

DIP switch setting

Set the DIP switch SET 4 SW3 referring to the Table C.
Indoor unit
RC AD SW
3
DIP switch (SET 4)
OFF
SW1
SW2
SW3
6 7
SW4
6 7
E F
Table C
14 15
DIP switch SET 4 SW3
OFF (Factory setting)
NOTE :
Please do not make a standard setup and an extension setup intermingled in remote
controller group.

6.4. Function setting

• FUNCTION SETTING can be performed with the wired or wireless remote controller.
(The remote controller is optional equipment)
• Refer to the wired or wireless remote controller manual for detailed setting information.
D
(Set IU AD, REF AD SW to 0)
• Refer to "6.1. Setting the address" for indoor unit address and refrigerant circuit ad-
dress settings.
• Turn the power of the indoor unit ON before starting the setting.
D
* Turning on the power to the indoor units initializes EEV, so make sure the piping air
tight test and vacuuming have been conducted before turning on the power.
* Also check again to make sure no wiring mistakes were made before turning on the
power.
Function details
Controller PCB
Function
Function
number
Filter
indicator 11
interval
Filter
indicator 13
action
C D
Cool air
OFF ON
temperature 30
trigger
ON ON
Heat air
temperature 31
trigger
Auto
40
restart
Cool Air
Preven- 43
tion
ON
SET 4
Cooling temperature setting range
Standard (18 to 30 °C)
ON Extension (18 to 32 °C)
Setting number Default
○
00 Default
Adjust the fi lter cleaning interval notifi ca-
tion. If the notifi cation is too early, change
01 Longer
to setting 01. If the notifi cation is too late,
change to setting 02.
02 Shorter
○
00 Enable
01 Disable Enable or disable the fi lter indicator. Set-
ting 02 is for use with a central remote
Display only
controller.
on central
02
remote
controller
○
00 Default
Adjust the cool air trigger temperature. To
lower the trigger temperature, use setting
01 Adjust (1)
01. To raise the trigger temperature, use
setting 02.
02 Adjust (2)
○
00 Default
Adjust the heat air trigger temperature. To
lower the trigger temperature by 6 degrees C,
01 Adjust (1)
use setting 01. To lower the trigger tempera-
02 Adjust (2)
ture by 4 degrees C, use setting 02. To raise
the trigger temperature, use setting 03.
03 Adjust (3)
00 Enable
Enable or disable automatic system
○
restart after a power outage.
01 Disable
○
00 Super low
Restrain the cold airfl ow with making the
airfl ow lower when starting heating op-
Follow the
eration. To correspond to the ventilation,
setting on
01 set to 01.
the remote
controller
Controller PCB
Details
7/12/2012 3:05:25 PM 7/12/2012 3:05:25 PM