Elica Glide Serie Montage- Und Gebrauchsanweisung Seite 56

pressure of the room must not exceed 4
Pa (4 x 10 bar). This manual must be
5
stored for future consultation at any time.
If sold, transferred or moved, it must
remain with the device.
This device is marked in compliance with the European
Directive 2012/19/EC - UK SI 2013 No3113, Waste Electrical
and Electronic Equipment (WEEE). By ensuring that this
device is disposed of correctly, the user will help prevent
potential negative impacts on the environment and human
health.
The symbol on the device or documentation provided
indicates that this device must not be treated as domestic
waste, but must be taken to a suitable waste collection site for
the recycling of electrical and electronic appliances. Dispose
of it in accordance with local regulations for waste disposal.
For further information about the treatment, recovery and
recycling of this device, please contact your local authority,
the collection service for household waste or the shop from
where the device was purchased.
Device designed, tested and developed in compliance with
regulations on:
• Safety: EN/IEC 60335-1; EN/IEC 60335-2-6, EN/IEC 60335-
2-31, EN/IEC 62233.
• Performance: EN/IEC 61591; ISO 5167-1; ISO 5167-3; ISO
5168; EN/IEC 60704-1; EN/IEC 60704-2-13; EN/IEC 60704-3;
ISO 3741; EN 50564; IEC 62301.EN 60350-2;
• EMC: EN 55014-1; CISPR 14-1; EN 55014-2; CISPR 14-2;
EN/IEC 61000-3-3; EN/IEC 61000-3-12. Recommendations
for correct use in order to reduce the impact on the
environment: When you start cooking, turn the device on at
minimum speed, leaving it on for a few minutes when you
have finished cooking. Increase the speed only if there is a
large quantity of fumes and steam, using the Booster function
only in extreme cases. To keep the odour reduction system
running efficiently, replace the carbon filter/s when necessary.
To ensure the high performance of the grease filter, clean it
when necessary. To improve efficiency and minimise noise,
use the maximum duct diameter indicated in this manual.
2. Use
Using the hob
The induction cooking system is based on the physical
phenomenon of magnetic induction. The main characteristic of
this system is the direct transfer of energy from the generator
to the pot.
Advantages:
When compared to electric hobs, your induction hob is:
- Safer: lower temperature on the glass surface.
- Faster: shorter food heating times.
- More accurate: the hob immediately reacts to your
commands
- More efficient: 90% of the absorbed energy is transformed
into heat. Moreover, once the pot is removed from the hob,
heat transmission is immediately interrupted, avoiding
unnecessary heat losses.
2.1 Cooking containers
Use only pots bearing the symbol
Important:
to avoid permanent damage to the hob surface, do not use:
- containers with less than perfectly flat bottoms.
- metal containers with enamelled bottoms.
- containers with a rough base, to avoid scratching the hob
surface.
- never place hot pots and pans on the surface of the hob's
control panel
2.1.1 Pre-existing containers
Induction cooking uses magnetism to generate heat.
Containers must therefore contain iron. Check if the pot
material is magnetic using a magnet. Pots are not suitable if
they are not magnetically detectable.
2.1.2 Recommended pan bottom diameters
IMPORTANT: if the pots are not correctly sized, the
cooking zones will not turn on
For details of the minimum pot diameter that needs to be used
on each zone, see the illustrated part of this manual.
2.2 Energy saving
Recommendations for best results:
- Use pots and pans with a bottom diameter equal to that of
the cooking zone.
- Use only pots and pans with flat bottoms.
- Where possible, keep the lid on pots during cooking
- Cook vegetables, potatoes, etc. with a minimal amount of
water to reduce cooking time.
- Use a pressure cooker, as it further reduces the energy
consumption and cooking time
- Place the pot in the centre of the cooking zone outlined on
the hob.
Using the extractor fan
The extraction system can be used in two versions: external
extraction and evacuation or as a filter with internal
recirculation.
Extraction version
The fumes are evacuated towards the outside through a
series of pipes (bought separately) fastened to the supplied
connecting flange.
The diameter of the exhaust pipe must be equivalent to the
diameter of the connecting ring:
- for rectangular outlets 222 x 89 mm
- for circular outlets Ø 150 mm (*)
For more information, see the page relative to the extraction
version in the illustrated part of this manual. Connect the
product to wall-mounted exhaust pipes and holes with a
diameter equivalent to the air outlet (connecting flange).
55