Siemens SINUMERIK 840D sl Handbuch Seite 207

03/2009
26020 NIBBLE_SIGNAL_CHECK
- Alarm bei Wackeln des Stanzsignales
-
- -
27100 ABSBLOCK_FUNCTION_MASK
- Satzanzeige mit Absolutwerten parametrieren
-
- -
27200 MMC_INFO_NO_UNIT
- HMI Info (ohne physikalische Einheit)
-
- 80
27201 MMC_INFO_NO_UNIT_STATUS
- HMI Statusinfo (ohne physikalische Einheit)
-
- 80
27202 MMC_INFO_POSN_LIN
mm HMI Info (linear Positionen)
-
- 50
27203 MMC_INFO_POSN_LIN_STATUS
- HMI Statusinfo (linear Positionen)
-
- 50
27204 MMC_INFO_VELO_LIN
mm/min HMI Info (linear Geschwindigkeiten)
-
- 16
27205 MMC_INFO_VELO_LIN_STATUS
- HMI Statusinfo (linear Geschwindigkeiten)
-
- 16
27206 MMC_INFO_CUT_SPEED
m/min HMI Info (Schnittgeschwindigkeiten)
-
- 5
27207 MMC_INFO_CUT_SPEED_STATUS
- HMI Statusinfo (Schnittgeschindigkeiten)
-
- 5
© Siemens AG 2009 All Rights Reserved
SINUMERIK 840D sl, 840Di sl, SINAMICS, Listen (LIS1sl), 03/2009
0,0,0,0,0,0,0,0,0,0,0,0,0 -
,0,0,0
0x0,0x0,0x0,0x0,0x0,0x 0
0,0x0,0x0,0x0...
45., 2., 0., 1., 0., -1., 0., -
1., 100., 1., 1., 0., 0., 0.,
0....
1, 1, 1, 1, 1, 1, 1, 1, 1, 1, -
1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
1...
0., 0., 1., 1., 0., 0., -
100., 0., 0., 1000., 1.,
1....
1, 1, 1, 1, 1, 1, 1, 1, 1, 1, -
1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
1...
10., 10., 2000., 10000., -
300., 1000., 1000., 10.,
0.,0.,0.,0....
1,1,1,1,1,1,1,1,0,0,0,0,0 -
,0,0,0...
100.,0.,0.,0.,0.,100.,0.,0 -
.,0.,0....
1,0,0,0,0,1,0,0,0,0,1,0,0 -
,0,0...
Maschinen- und Settingdaten
Kanalspezifische NC-Maschinendaten
C09 N4
DWORD POWER ON
- 7/2
N01 K1,P1
DWORD POWER ON
0x1 7/2
EXP, - -
DOUBLE POWER ON
- 0/2
EXP, - -
BYTE POWER ON
- 0/2
EXP, - -
DOUBLE POWER ON
- 0/2
EXP, - -
BYTE POWER ON
- 0/2
EXP, - -
DOUBLE POWER ON
- 0/2
EXP, - -
BYTE POWER ON
- 0/2
EXP, - -
DOUBLE POWER ON
- 0/2
EXP, - -
BYTE POWER ON
- 0/2
2-207